Service Bulletins| Name | Revision | Lang | Subject | Date |
|---|
| SB 5-A-PM5987 |
Iss 2 |
en |
Alert Time Limits - Aircraft General - Corrosion Control Program - Requirement Arising from the Airworthiness Assurance Task Unit Activity | 06/30/1992 |
| SB 5-A-PM5995 |
Iss 3 |
en |
Mandatory Alert Time Limits - Aircraft General - Structural Maintenance Inspection and Modification Review - Requirements Arising from the Aging Aircraft Task Unit Activity | 03/19/1993 |
| SB 6/5 |
|
en |
Mandatory Nose Undercarriage Retraction Jack Support Structure and Front Pressure Bulkhead - Fatigue Cracking | 09/04/1978 |
| SB 6/5500/F-61-A12 |
|
en |
Alert Propellers - Transfer Tubes - New Transfer Tube Part Numbers | 10/27/1992 |
| SB 7/3 |
|
en |
Mandatory Inspection of Wing Bottom Skin Panels at Main Undercarriage Bay | 09/30/1980 |
| SB 7/5 |
1 |
en |
Mandatory Main Landing Gear Hinge Fittings - Bolts Loose | 05/23/1988 |
| SB 7/8 |
3 |
en |
Mandatory Main Landing Gear Hinge Fitting & Support Angle Cracking | 05/23/1988 |
| SB 9/10 |
|
en |
Mandatory Rudder Pedal Adjusting Mounting Bracket | 04/28/1981 |
| SB 11-97-01285A |
1 |
en |
Mandatory Placards and Markings - N2 Limitations for Anti-Ice Selection - To Introduce a Placard on the Flight Deck Overhead Panel and Wiring to Inhibit the Airbrake Auto-Retract Function | 04/03/1992 |
| SB 11-137-30405A |
|
en |
Mandatory Placard/Markings - To Introduce a Flight Deck Placard on the Centre Instrument Panel to Indicate that 26,000 Ft Altitude Icing Limitations are Applicable and to Introduce a New Replacement Placard to the Ice Protection Panel for N2 Limitations | 03/26/1998 |
| SB 21-162 |
1 |
en |
Air Conditioning - Inspection for Cracking of Skin at Front and Rear Discharge Valves | 09/16/2010 |
| SB 21-162 |
4 |
en |
Air Conditioning - Inspection for Cracking of Skin at Front and Rear Discharge Valves | 01/28/2015 |
| SB 22-072-36262A |
|
en |
Autopilot - BAe 146 Autopilit Disconnect via Electric Pitch Trim System | 09/14/2021 |
| SB 22-A-JA 851231 |
|
en |
Autopilot - Elevator Trim System Friction Check and Electric Trim Manual Override Load Check | 04/09/1986 |
| SB 22-A-JA 860413 |
|
en |
Mandatory Autopilot - Replacement of Elevator Trim Servo Motor | 04/16/1986 |
| SB 22-JK 2628 |
2 |
en |
Autoflight - Introduction of Additional Trim Relays in the Autopilot System to Remove the 800 Hour Life Cycle Restriction | 10/21/1996 |
| SB 22-JK 2628 |
Err 1 |
en |
Autoflight - Introduction of Additional Trim Relays in the Autopilot System to Remove the 800 Hour Life Cycle Restriction | 04/25/1997 |
| SB 23-36-01238A |
|
en |
Communications - Audio Integration - To Introduce a Revised Minimum Standard of the Central Audio Unit | 12/21/1990 |
| SB 24-82-36097A&B |
|
en |
Electrical Power - AC Power Distribution - To Introduce Erma in-Line Splice Pt. No. 12198/2 in Place of Pt. No. 12197/2, or a Continuos Run of Twisted Wires, for APU Generator Feeder Cables | 02/11/1991 |
| SB 24-83 |
|
en |
Mandatory Electrical Power - Inspection of in-Line Splices in APU Generator Circuit for Overheating | 01/22/1991 |
| SB 24-83-50134A |
1 |
en |
Electrical Power - AC Power Distribution - To Introduce Erma in-Line Splice Pt. No. 12198/2 in Place of Pt. No. 12197/2 for APU Generator Feeder Cables | 03/15/1991 |
| SB 24-84 |
|
en |
Mandatory Electrical Power - Inspection of in-Line Splices in the Integrated Drive Generator Circuits for Overheating | 01/22/1991 |
| SB 24-84-50134B |
1 |
en |
Electrical Power - AC Power Distribution - To Introduce Erma in-Line Splice Pt. No. 12198/2 in Place of Pt. No. 12197/2 for Integrated Drive Generator Feeder Cables | 03/15/1991 |
| SB 24-85-01253A |
1 |
en |
Electrical Power - AC Power Distribution - To Introduce Erma Splice Pt. No. 12198/2 in Place of Pt. No. 12197/2 for Integrated Drive Generator Feeder Cables | 03/15/1991 |
| SB 24-91-70488B&C |
1 |
en |
Mandatory Electrical Power - Generator Control Unit - Introduction of GEC MOD Nos. 1404 Issue 2 and 1409 Issue 1 to Generator Control Unit 700-1-22490-400 and Generator Control Unit 700-1-22490-500 and to Delete the Neutral Connection from the Vickers Pump | |
| SB 24-91-70488B&C |
2 |
en |
Mandatory Electrical Power - Generator Control Unit - Introduction of GEC MOD Nos. 1404 Issue 2 and 1409 Issue 1 to Generator Control Unit 700-1-22490-400 and Generator Control Unit 700-1-22490-500 and to Delete the Neutral Connection from the Vickers Pump | 07/19/1993 |
| SB 24-103 |
|
en |
Mandatory Electrical Power - AC Generation - Inspection of Generator Control Units for Possible Incorrect Under-Frequency Trip Level Settings | 03/24/1994 |
| SB 24-107 |
|
en |
Mandatory Electrical Power - DC Generation - Inspection of Terminal Block on DC Panel No. 1 for Presence of Two-Way Link | 01/25/1995 |
| SB 24-113-01532A |
|
en |
Mandatory Electrical Power - To Increase the Size of the Generator Feeder Cables Between AC1/AC2 Busbars and the Generator Contractors | 03/12/1996 |
| SB 24-113-01532A |
1 |
en |
Mandatory Electrical Power - To Increase the Size of the Generator Feeder Cables Between AC1/AC2 Busbars and the Generator Contractors | 06/18/1996 |
| SB 24-120 |
|
en |
To Inspect Erma Terminal Lugs in the Electrical Equipment Bay and Hydraulic Equipment Bay | 09/18/1997 |
| SB 24-143 |
1 |
en |
Electrical Power - Insulation Resistance Testing of Ceramic Terminal Blocks | 10/02/2012 |
| SB 24-220-(2749) |
3 |
en |
Mandatory Electrical Power - Distribution - Panel 'ZL' Addition of Protective Covers | 03/03/1983 |
| SB 24-225-(2747) |
|
en |
Mandatory Electrical Power - Fuel Computers DC Power Supply Transferred to 'PE' Busbar from 'PE2' Busbar | 10/17/1980 |
| SB 24-230-(2790) |
3 |
en |
Mandatory Electrical Power - Electrical Interference Suppression | 06/11/1982 |
| SB 24-239-(2885) |
1 |
en |
Mandatory Electrical Power - Load Distribution - To Introduce Uprated Feeder Fuses in the 'PE' Busbar Circuits on Panel 'ZL' | 02/27/1984 |
| SB 24-248-(3024) |
|
en |
Mandatory Electrical Power - EFIS Power Supply - Revised Heat Sink Sub-Assembly | 03/08/1985 |
| SB 24-250-(3017D) |
|
en |
Mandatory Electrical Power - Panel 'DA' - Improved Protection for Electrical Cables | 04/08/1985 |
| SB 24-251-(3014A) |
|
en |
Mandatory Electrical Power - Revised Signal Summing Unit Earth Connections | 04/08/1985 |
| SB 24-256-(3171B) |
|
en |
Mandatory Electrical Power: Panel ZK - Panel Extension Revised | 10/31/1986 |
| SB 24-261-3204A&B |
1 |
en |
Mandatory Electrical Power - Wiring Installation - Rerouting of Wiring Installation at Panel LZ | 03/24/1988 |
| SB 24-263-9486A |
1 |
en |
Mandatory Electrical Power - Smoke Drill - Additional Circuit Breaker Identification Labels | 01/27/1988 |
| SB 24-268-3223A&B |
3 |
en |
Mandatory Electrical Power - Starting - Hartman Contractor Ai48MAS, A848KHS, A848KSS Mounting Arrangement Revised | 04/25/1989 |
| SB 24-270 |
|
en |
Mandatory Electrical Power - Cable Installation - Chafing of Electrical Cable Looms above Panel DA-E | 03/20/1989 |
| SB 24-279-3255A |
|
en |
Mandatory Electrical Power - Constant Frequency System - Introduction of a Cover for the Standby Inverter | 11/16/1990 |
| SB 24-288-3284A |
|
en |
Mandatory Electrical Power - Smoke Drill - Introduction of White Indicator Labels to Windscreen Heat Power Supply Circuit Breakers | 02/07/1992 |
| SB 24-289-3267A-G |
1 |
en |
Mandatory Electrical Power - Generator Power - To Introduce Additional Generator Control Arrangements and Relocate GCU Earth Wires | 04/10/1992 |
| SB 24-A-JA 900443 |
2 |
en |
Mandatory Alert Electrical Power - Deletion of Inverter Transfer Function | 11/15/1990 |
| SB 24-A-JM 7708 |
1 |
en |
Mandatory Alert Electrical Power - Introduction of Switching of Inverter Synchronization Lines by Transfer Switch | 05/22/1990 |
| SB 24-A97 |
|
en |
Mandatory Alert Electrical Power - AC Generation - Possible Failure of Generator Control Unit to Detect a Single Phase Feed Line Open Circuit | 11/12/1991 |
| SB 24-A261 |
1 |
en |
Mandatory Alert Electrical Power - Cable Installation - Chafing of Wire at Panel ZL | 08/17/1987 |
| SB 24-A278 |
|
en |
Mandatory Alert Electrical Power - DC Generation System - Inspection of Generator Control Unit Earth Wire at Starter/Generator Terminal Block | 07/26/1990 |
| SB 25-20-2658 |
|
en |
Alert Hydrolok Pin Orientation | 11/12/2001 |
| SB 25-54-9758A&B |
1 |
en |
Mandatory Equipment/Furnishings - Warning Oven - Introduce Warning Oven Part Nos. 255D-LH-28/115, 255D-RH-28/115 and 255-362A with Overheat Protection | 08/14/1989 |
| SB 25-67-25A013A |
2 |
en |
Mandatory Equipment/Furnishings - To Introduce an Improved Washbasin Watertank Shroud Drain Outlet | 10/18/1991 |
| SB 25-328 |
2 |
en |
Mandatory Equipment/Furnishings - Emergency Equipment - Possible Failure of Evacuation Slide to Deploy Automatically on Demand | 07/10/1993 |
| SB 26-077-36250A.B |
4 |
en |
Fire Protection - Introduction of Revised Baggage Bay Fire Bottle Wiring and Clipping Arrangement | 01/07/2011 |
| SB 26-078 |
|
en |
Inspection of Fire Bottles for Excessive Solder Between Operating Head and Container | 09/21/2011 |
| SB 26-27 |
|
en |
Mandatory Fire Protection - Fire Warning System - Possible Incorrect Crimping of Connector Socket Contacts | 05/16/1986 |
| SB 26-31 |
|
en |
Mandatory Fire Protection - Inspection of Engine Fire Extinguisher Electrical Connections for Security, Identification Tags and Wire Locking | 02/25/1991 |
| SB 26-32-36128A |
|
en |
Mandatory Fire Protection - Smoke Detection - To Introduce a Resonator to the Warning Horn of the Forward and Rear Toilet Smoke Detectors | 04/30/1992 |
| SB 26-35 |
1 |
en |
Mandatory Fire Protection - APU Bay Forward Firewall - Inspection of Firewall for Cracking | 08/30/1995 |
| SB 26-35-36179A |
|
en |
Fire Protection - APU Bay Firewall - To Introduce a Revised Material Specification for the Centre Portion of the Forward Bulkhead | 08/04/1995 |
| SB 26-36-36179B |
|
en |
Mandatory Fire Protection - To Introduce Protective Shield for Auxiliary Power Unit (APU) Fire Bottle Wiring - (Allied Signals - 150M APU) | 06/22/1995 |
| SB 26-40-01601A |
|
en |
Fire Protection - To Re-Install BAe Firewire Mounting Bracket to Same Location as Allied Signal Anti-Ice Valve Mounting Bracket (Introduced by Allied Signal Service Bulletin ALF/LF72-1020) and Re-Route the Firewire | 03/25/1998 |
| SB 26-44 |
|
en |
Fire Protection - Detection - Inspection for Chafing Damage by Powerplant Firewire Responder Unit(s) on Adjacent Fuel Pipe | 02/25/1999 |
| SB 26-A25 |
2 |
en |
Mandatory Alert Fire Protection - Fire Extinguishing System - Incorrect Circuit Wiring | 03/26/1985 |
| SB 26-A29 |
2 |
en |
Mandatory Alert Fire Protection - Extinguishing - Inspection of Extinguisher Pipe Assembly in Engine Nose Cowl | 01/14/1991 |
| SB 27-70-00913A&B |
7 |
en |
Mandatory Flight Controls - To Introduce an Amber Warning Light 'Lift Spoilers Not Deployed' | 03/21/1994 |
| SB 27-77-00955A&C |
2 |
en |
Mandatory Flight Controls - Elevator Control System - To Introduce an Elevator "G" Weight Damper, and a Single Acting Spring Strut to Increase Column Centring Force | 03/10/1989 |
| SB 27-114-01028B |
|
en |
Mandatory Flight Controls - Stall Identification and Warning System - Signal Summit Unit (SSU) - To Introduce Safe Flight SSU C81606-6 (Incorporating Correct Airspeed Law) in Place of C81606-4 | 09/26/1990 |
| SB 27-124-(2705) |
|
en |
Mandatory Flight Controls -To Remount the Elevator Pitch Trim Switch on the Control Column Handwheel | 01/01/1979 |
| SB 27-125 |
|
en |
Mandatory Flight Controls - Flap Jack Assembly Component Ultimate Lives | 03/19/1979 |
| SB 27-133 |
|
en |
Mandatory Flight Controls - Airbrake System - Possible Failure of Feedback Spring in Servo-Valve Assembly | 01/31/1992 |
| SB 27-135 |
|
en |
Mandatory Flight Controls - Pitch Servomotor - Possible Incorrect Drilling of Foul Pin Holes in Servomotor Mounting Bracket | 04/23/1992 |
| SB 27-136-3059A |
1 |
en |
Mandatory Flight Controls - Stall Identification System - Revised Flap Microswitch Layshaft | 06/24/1985 |
| SB 27-137 |
|
en |
Mandatory Flight Controls - Lift Spoiler System - Possible Dormant Failure of "Lift Spoiler Unlocked" Indication System | 11/17/1992 |
| SB 27-140 |
1 |
en |
Mandatory Flight Controls - Flap System - Inspection of Torque Shaft Assemblies | 08/04/1986 |
| SB 27-142 |
2 |
en |
Mandatory Flight Controls -Elevator Mass Balance - Possible Corrosion of Balance Weight Sideplate Assembly and Spigot | 06/10/1987 |
| SB 27-142 |
3 |
en |
Mandatory Flight Controls -Elevator Mass Balance - Possible Corrosion of Balance Weight Sideplate Assembly and Spigot | 11/13/1989 |
| SB 27-149 |
|
en |
Mandatory Flight Controls - Stall Identification System - Detachment of Balance Weight Insert from Airflow Angle Sensor Vane | 03/17/1989 |
| SB 27-150-01510B |
|
en |
Flight Controls - Elevators - To Introduce Up-Rated Elevator Springs | 12/15/1995 |
| SB 27-155 |
|
en |
Mandatory Flight Controls - Inspection of Rudder Pedal Torque Tubes for Cracking | 08/16/1991 |
| SB 27-A-JA 910340 |
|
en |
Mandatory Alert Flying Controls - Changes in Operational Procedures for Landing in Icing Conditions, and Associated Changes to Aircraft Modification Standard | 03/25/1991 |
| SB 27-A-JA 910340 |
1 |
en |
Mandatory Alert Flying Controls - Changes in Operational Procedures for Landing in Icing Conditions, and Associated Changes to Aircraft Modification Standard | 10/02/1991 |
| SB 27-A-JA 911044 |
|
en |
Mandatory Alert Flying Controls - Changes in Operational Procedures for Landing in Icing Conditions, and Associated Changes to Aircraft Modification Standard | 01/31/1992 |
| SB 27-A-JA 980606 |
1 |
en |
Mandatory Alert Flight Controls - Elevator - Failure of the Baring in the Bias Spring Assembly | 07/31/1998 |
| SB 27-A-JM7847 |
1 |
en |
Mandatory Alert Flying Controls - Stall Warning and Protection System - Removal of the Ground Inhibit Function | 04/27/1998 |
| SB 27-A-PM3034 |
Iss 2 |
en |
Flap Secondary Transmission Shaft - Failure | 12/06/1967 |
| SB 27-A-PM5341 |
Iss 3 |
en |
Mandatory Alert Flight Controls - Flap Secondary Drive Shafting - Failure | 09/28/1981 |
| SB 27-A-PM5341 |
Iss 4 |
en |
Mandatory Alert Flight Controls - Flap Secondary Drive Shafting - Failure | 05/06/1991 |
| SB 27-A-PM6005 |
|
en |
Mandatory Alert Stall Protection - Static Inverter | 03/28/1990 |
| SB 27-A-PM6005 |
Iss 2 |
en |
Mandatory Alert Stall Protection - Static Inverter | 06/17/1991 |
| SB 27-A-PM6007 |
|
en |
Mandatory Alert Spoiler Torque Shaft - Corrosion | 04/10/1992 |
| SB 27-A-PM6023 |
Iss 2 |
en |
Mandatory Alert Flying Controls - Corrosion of Aileron Control Bearings | 11/23/1992 |
| SB 27-A-PM6025 |
|
en |
Mandatory Alert Flight Controls - Cracking of Levers and Brackets Manufactured from L53 Material | 03/23/1994 |
| SB 27-A-PM6034 |
|
en |
Mandatory Alert Flying Controls - Lift Dumper Operating Mechanism Rod Eye Ends | 10/06/1995 |
| SB 27-A-PM6041 |
|
en |
Mandatory Alert Flight Controls - Cracking of Flap Control Lever Manufactured from L53 Alloy | 08/21/1998 |
| SB 27-JA181040 |
|
en |
Flying Controls - Inspection of Rudder & Elevator Flight Control Cable Terminals for Corrosion | 01/17/2019 |
| SB 27-JA 910541 |
3 |
en |
Flying Controls - Introduction of a Landing Flap Setting of 35 Degrees in Lieu of 50 Degrees and Re-Defined Ground Idle Power Lever Position | 11/16/1992 |
| SB 27-JA 920340 |
2 |
en |
Flight Controls - Introduction of an Improved Flap Torque Shaft Assembly | 12/21/1993 |
| SB 27-JM 5350 |
1 |
en |
Flight Controls - Introduction of Modified Push Rod Assembly at Gustlock/Power Lever Baulk Mechanism | 05/06/1994 |
| SB 27-PM4642 |
1 |
en |
Flight Controls - To Record Hobson Mods, To Improve Bearing Support Assemblies | 10/12/1970 |
| SB 27-PM6005 |
|
en |
Mandatory Alert Stall Protection - Static Inverter | 06/11/1991 |
| SB 28-18 |
|
en |
Mandatory Fuel - Centre Section Tank - Inspection of Polymer Coating Around Centre Section Fuel Tank and on Frames 26 and 29 | 03/12/1991 |
| SB 28-67 |
1 |
en |
Mandatory Fuel - Pressure Refuel/Defuel System - Failure of HTE "V" Clamps | 12/19/1978 |
| SB 28-69 |
1 |
en |
Mandatory Fuel - Distribution - Possible Foul Between Fuel Pipe and Flap Input Lever | 06/25/1979 |
| SB 28-86 |
|
en |
Mandatory Fuel - Inspection of Fuel Feed Pipe Joints for Misalignment at Pipe Entry into Coupling | 06/28/1991 |
| SB 28-87 |
|
en |
Mandatory Fuel - Inspection of Fuel Feed Pipe Joints for Misalignment at Pipe Entry into Coupling | 12/31/1991 |
| SB 28-A-JA 990841 |
|
en |
Mandatory Alert Fuel - Quantity Indication - Damaged Insulation on Wires to the Contents Units in the Fuel Tanks | 09/08/1999 |
| SB 28-A-JA 990841 |
1 |
en |
Mandatory Alert Fuel - Quantity Indication - Damaged Insulation on Wires to the Contents Units in the Fuel Tanks | 11/12/1999 |
| SB 28-A66 |
|
en |
Alert Fuel - Pressure Refuel/Defuel System - Failure of HTE "V" Clamps | 10/03/1978 |
| SB 28-JM 7161 |
|
en |
Mandatory Fuel System - Reposition of Crossfeed Pipe to Obviate Fuel Pipe Fracture in the Event of a Wheels Up Landing | 12/19/1983 |
| SB 29-048-30676A |
2 |
en |
Mandatory Hydraulics - Introduction of a Hydraulic Fluid Containment System | 12/23/2010 |
| SB 29-31-01339A |
|
en |
Mandatory Hydraulic Power - To Introduce an Improved Fire Resistant Quick Release Coupling Half for the Engine Driven Pump (EDP) Case Drain Lines in the Engine Bay | 05/24/1993 |
| SB 29-31-01339A |
1 |
en |
Mandatory Hydraulic Power - To Introduce an Improved Fire Resistant Quick Release Coupling Half for the Engine Driven Pump (EDP) Case Drain Lines in the Engine Bay | 07/08/1993 |
| SB 29-89-3269A |
|
en |
Mandatory Hydraulic Power - Rear Fuselage - Introduction of a Charging Instruction Label for Hydraulic System Accumulators | 05/22/1992 |
| SB 29-A-JA881143 |
|
en |
Mandatory Alert Hydraulic Power - Introduction of a Modification to the Detent Ball Catch of the Emergency Selector Valve | 02/24/1989 |
| SB 29-JA 901242 |
|
en |
Mandatory Hydraulic Power - Emergency Selector Valve - Introduction of an Inspection to Check Operating Load | 06/18/1991 |
| SB 29-JA 901242 |
1 |
en |
Mandatory Hydraulic Power - Emergency Selector Valve - Introduction of an Inspection to Check Operating Load | 09/25/1991 |
| SB 29-JM 7360 |
1 |
en |
Mandatory Hydraulic Power - To Introduce Revised Handle, Stowage and Access for Hydraulic Hand-Pump | 01/03/1991 |
| SB 30-025 |
|
en |
Ice and Rain Protection - Inspection of Wing Leading Edge Anti-Icing Piccolo Tube End Cap | 04/19/2011 |
| SB 30-A-JA 920444 |
|
en |
Mandatory Alert Ice and Rain Protection - Inspections and Introduction of Revised Pipes and Hoses in the Tail Unit De-Icing System | 10/30/1992 |
| SB 30-JA 950641 |
|
en |
Mandatory Ice and Rain Protection - Windshield Wipers - Service Life of Arm Assembly and Attachment Bold | 08/23/1996 |
| SB 30-JA 950641 |
1 |
en |
Mandatory Ice and Rain Protection - Windshield Wipers - Service Life of Arm Assembly and Attachment Bold | 10/21/1996 |
| SB 30-JA 950641 |
2 |
en |
Mandatory Ice and Rain Protection - Windshield Wipers - Service Life of Arm Assembly and Attachment Bold | 03/18/1997 |
| SB 30-JK 12033 |
1 |
en |
Ice and Rain Protection - Changes to Airframe De-Ice Automatic Switch | 10/20/1995 |
| SB 30-JM 7453 |
2 |
en |
Mandatory Ice and Rain Protection - Introduction of Improved Propeller De-Icing System | 12/10/1984 |
| SB 32-36 |
|
en |
Langing Gear - Main Gear - Fit Cylinder Manufactured from New Material | 07/20/1988 |
| SB 32-46 |
|
en |
Landing Gear - Main Gear - Fit Flanged Axle Nut | 04/09/1991 |
| SB 32-103 |
1 |
en |
Landing Gear - Main Landing Gear Extension and Retraction - Possible Forging Defects in Body of MLG and Door Lock Jack Assemblies | 02/22/1991 |
| SB 32-124-70491A&B |
1 |
en |
Mandatory Landing Gear - Brake Controls and Indication - To Introduce Improved Anti Skid Control Boxes | 11/25/1991 |
| SB 32-124-70491A&B |
2 |
en |
Mandatory Landing Gear - Brake Controls and Indication - To Introduce Improved Anti Skid Control Boxes | 06/30/1992 |
| SB 32-130-70295C |
|
en |
Mandatory Landing Gear - Wheels and Brakes - To Introduce Dunlop Hydraulic Fuse Part No. ACM30506 Mod. 1 in Place of Existing Part No. ACM29100 Dunlop Mod. No. C2681 Refers | 09/27/1991 |
| SB 32-131 |
|
en |
Mandatory Landing Gear - Nose Landing Gear - Inspection of Upper Main Fitting for Possible Cracks | 12/06/1991 |
| SB 32-131 |
1 |
en |
Mandatory Landing Gear - Nose Landing Gear - Inspection of Upper Main Fitting for Possible Cracks | 11/12/1992 |
| SB 32-131 |
2 |
en |
Mandatory Landing Gear - Nose Landing Gear - Inspection of Upper Main Fitting for Possible Cracks | 07/10/1993 |
| SB 32-131 |
3 |
en |
Mandatory Landing Gear - Nose Landing Gear - Inspection of Upper Main Fitting for Possible Cracks | 10/18/1995 |
| SB 32-143 |
|
en |
Mandatory Landing Gear - Main Landing Gear - Inspection of the Direction Link Sub Assembly | 08/22/1995 |
| SB 32-144 |
|
en |
Mandatory Landing Gear - Main Landing Gear - Inspection of the Outer Link for Cracks | 12/11/1996 |
| SB 32-145 |
1 |
en |
Mandatory To Inspect Eye Bolt/Piston Rod of Main Landing Gear Retraction Jack for Corrosion | 10/06/1997 |
| SB 32-150-70656A |
|
en |
Mandatory Landing Gear - Introduction of New MLG Uplocks and MLG Door Locks with Revised Rollers | 12/01/1998 |
| SB 32-157 |
|
en |
Mandatory Landing Gear - Main Landing Gear Side Stay - NDT Inspection of Inner Sidestay for Cracking at Fuselage End (LH and RH) | 06/02/2000 |
| SB 32-176 |
|
en |
Landing Gear - MLG- Inspection of the Shock Absorber Lower Attachment Pin | 11/12/2009 |
| SB 32-184 |
4 |
en |
Mandatory Landing Gear - Nose Leg Drag Stay Assembly - Cracking of Bridge Casting | 04/10/1987 |
| SB 32-186 |
|
en |
Landing Gear - Introduction of Compliance Periods in Advance of a 16,000 Cycle Safe Life for Nose Landing Gear Main Fittings | 04/12/2012 |
| SB 32-190 |
|
en |
Mandatory Landing Gear - Main Gear - Possible Failure to Lower | 08/28/1981 |
| SB 32-193 |
2 |
en |
Mandatory Landing Gear - Wheels and Brakes - Replacement of Knife Edges of Unknown Life on Brake Control Valve AC61520 | 03/15/1984 |
| SB 32-216 |
1 |
en |
Mandatory Landing Gear - Main Landing Gear Sidestay Upper Arm - Introduction of an Ultimate Life | 03/21/1988 |
| SB 32-218 |
|
en |
Mandatory Landing Gear - Cracking of Main Gear Door Forward Hinge Fitting | 07/28/1988 |
| SB 32-220-3176A-C |
|
en |
Mandatory Landing Gear - Main Gar Fairings and Doors - To Introduce Steel Wing Attachment Casting for Main Gear Door Jack | 09/02/1988 |
| SB 32-222 |
|
en |
Mandatory Landing Gear - Main Landing Gear - Inspection of Main Landing Gear Torque Link Pivots | 11/10/1989 |
| SB 32-222-3244A |
1 |
en |
Landing Gear - Main Gear - Introduction of Improved Torque Link Pivot Arrangements | 03/05/1990 |
| SB 32-224 |
1 |
en |
Mandatory Landing Gear - Main Landing Gear - Inspect MLG Sidestay to Wing Pick Up Fitting for Adequate Clearance | 08/30/1990 |
| SB 32-225 |
|
en |
Mandatory Landing Gear - Main Landing Gear - Inspection of Main Landing Gear Sidestay Centre Pivot | 05/30/1990 |
| SB 32-226-3257A |
|
en |
Mandatory Landing Gear - Main Gear - Introduction of Steel Torque Links and Reduced Axial Clearances at Torque Link Pins and Knuckle Joints | 05/03/1991 |
| SB 32-227 |
1 |
en |
Mandatory Landing Gear - Main Landing Gear - Inspection of M.L.G. Side Stay Arm Assemblies and Torque Links | 10/12/1990 |
| SB 32-A-JA-980840 |
3 |
en |
Mandatory Alert Landing Gear - Nose Wheel Steering - Inspection for Correct Operation and Free Play in the Nose Wheel Steering System | 05/05/1999 |
| SB 32-A-JA140940 |
|
en |
Landing Gear - Inspection of Main Landing Gear Special Washer Installation | 10/03/2014 |
| SB 32-A-JA 850127 |
2 |
en |
Mandatory Alert Landing Gear - Inspection of Main Landing Gear Hinge Fitting and Support Angle | 11/11/1994 |
| SB 32-A-JA851226 |
5 |
en |
Landing Gear - To Introduce NDT and Visual Inspections of Main Landing Gear Spigot Housing for Cracks | 04/30/2013 |
| SB 32-A-JA851226 |
7 |
en |
Landing Gear - To Introduce NDT and Visual Inspections of Main Landing Gear Spigot Housing for Cracks | 05/25/2015 |
| SB 32-A-JA 910140 |
|
en |
Mandatory Alert Landing Gear - Introduction of a Wheel Retaining Nut Torque Check and an Improved Wheel Retaining Nut | 05/17/1991 |
| SB 32-A-JA 941245 |
3 |
en |
Mandatory Alert Landing Gear - Main Gear - Inspect Pintle to Cylinder Interface for Cracks | 03/15/1996 |
| SB 32-A-JA 980540 |
|
en |
Mandatory Alert Main Landing Gear - Brake Units - Inspection to Ensure Wear Indicator Pins are Correctly Set | 07/06/1998 |
| SB 32-A-PM3509 |
Iss 6 |
en |
Mandatory Alert Nose Landing Gear Sustaining Ram - Cracks in Vicinity of Ram Axle Lugs | 05/11/1977 |
| SB 32-A119 |
|
en |
Mandatory Alert Landing Gear - Main Landing Gear - Inspection of Door Rear Hinge Bracket Assemblies | 11/14/1990 |
| SB 32-A119 |
1 |
en |
Mandatory Alert Landing Gear - Main Landing Gear - Inspection of Door Rear Hinge Bracket Assemblies | 12/02/1991 |
| SB 32-A189 |
|
en |
Alert Landing Gear - Main Landing Gear Sidestay - Inspection of Outer Link (LH & RH) for Cracks & Dimensional Checks | 09/16/2022 |
| SB 32-A189 |
2 |
en |
Alert Landing Gear - Main Landing Gear Sidestay - Inspection of Outer Link (LH & RH) for Cracks & Dimensional Checks | 08/03/2023 |
| SB 32-A197 |
|
en |
Mandatory Alert Landing Gear - Extension and Retraction - Cracking of Main Gear Jack Cylinder Head Attachment Lugs | 08/29/1983 |
| SB 32-JA 000342 |
|
en |
Mandatory Nose Landing Gear - Introduction of Steering Actuator with Modified Piston Rod | 05/05/2000 |
| SB 32-JA 030644 |
|
en |
Landing Gear - Inspection of Steering Jack Piston for Cracks, and Determination of a Component Safe Life | 10/06/2003 |
| SB 32-JA090240 |
|
en |
Wings - Inspection of Main Undercarriage Fitting | 04/29/2009 |
| SB 32-JA090240 |
1 |
en |
Wings - Inspection of Main Undercarriage Fitting | 01/18/2010 |
| SB 32-JA880340 |
|
en |
Landing Gear - To Introduce Main Landing Gear with Cylinders Manufactured from L161 Material | 01/06/1989 |
| SB 32-JA 900942 |
5 |
en |
Mandatory Landing Gear - Introduction of New Nose Wheel Steering Jack Seals | 09/04/1998 |
| SB 32-JA 901040 |
3 |
en |
Mandatory Landing Gear - Fit New or Modified Top Cap Assembly and Check Length of Bolts on Nose Landing Gear | 08/09/1995 |
| SB 32-JA 960142 |
|
en |
Mandatory Landing Gear - Main Gear - To Introduce Repeat Inspection of Pintle to Cylinder Interface for Cracks | 03/15/1996 |
| SB 32-JA960142 |
5 |
en |
Mandatory Landing Gear - Main Gear - To Introduce Repeat Inspection of Pintle to Cylinder Interface for Cracks | 12/13/2019 |
| SB 32-JA 960601 |
|
en |
Mandatory Alert Landing Gear - Nose Gear - Measurement of Material Thickness at the Toggle Attachments | 10/25/1996 |
| SB 32-JA 981043 |
|
en |
Mandatory Landing Gear - Nose Landing Gear - Lubrication and Free Movement Check of Steering Jack | 03/05/1999 |
| SB 32-JA 991140 |
|
en |
Mandatory Landing Gear - Inspection of Main Landing Gear Radius Rod | 04/14/2000 |
| SB 32-JM 7493 |
1 |
en |
Landing Gear - Introduction of Audible Warning on Selection of 20 Degree Flap with Landing Gear Up | 03/25/1991 |
| SB 32-JM 7862 |
1 |
en |
Landing Gear - Introduction of Special Washer to Protect the Main Landing Gear Cylinder at the Forward Spigot | 05/07/2013 |
| SB 32-JM 7862 |
3 |
en |
Landing Gear - Introduction of Special Washer to Protect the Main Landing Gear Cylinder at the Forward Spigot | 10/03/2014 |
| SB 32-PM 2437 |
|
en |
Landing Gear - To Shot Peen and Roto Finish the Belleville Washers in the Main and Nose Undercarriage Lock Jacks to Improve Fatigue Life | 07/27/1966 |
| SB 32-PM 2898 |
1 |
en |
Landing Gear - Main Undercarriage - To Increase the Diameter of the Lower Sidestay Pin Retaining Bolt for the Main Undercarriage | 04/10/1967 |
| SB 32-PM 4538 |
1 |
en |
Mandatory Landing Gear - To Provide Indication When the Undercarriage Selection Lever is Not in its Gated Position | 08/27/1970 |
| SB 32-PM 6054 |
|
en |
Landing Gear Brake Accumulator Replacement | 01/31/2000 |
| SB 32A-75 |
1 |
en |
Mandatory Landing Gear - Brakes - Possible Failure of Stator Drives | 04/10/1987 |
| SB 33-44-7670A |
1 |
en |
Mandatory Lights - Instrument Integral Lighting - Introduction of Revised Circuitry in Dimmer Unit D492-05-001 | 04/04/1991 |
| SB 33-45-25A027A&B |
|
en |
Mandatory Lights - Cabin and Toilet Fluorescent Lighting - Introduction of Power Units with an Integral Circuit for System Fault Protection | 12/23/1991 |
| SB 33-A-PM4169 |
Iss 4 |
en |
Mandatory Flight Deck Roof Centre Electrical Panel - Fire Protection | 06/07/1970 |
| SB 34-128-00950J |
|
en |
Mandatory Navigation - Pitot-Static System - To Introduce a Change in Length of Pitot-Static Hoses to the Instrument Panels | 03/22/1991 |
| SB 34-131-46041A |
|
en |
Mandatory Navigation - Pitot-Static System - To Correct Pitot and Static Flexible Hose Lengths for the TAS 1 Unit in the Avionics Rack on Pre Phase II Avionics Aircraft | 06/24/1991 |
| SB 34-132-46042A |
|
en |
Mandatory Navigation - Pitot-Static System - To Correct Pitot and Static Flexible Hose Lengths for the TAS 2 Unit in the Avionics Rack on Pre Phase II Avionics Aircraft | 06/24/1991 |
| SB 34-160-70548A |
|
en |
Mandatory Navigation - To Introduce Safe Flight Windshear Computer Part No. 6508-5 which Incorporates Flap Input Open Circuit Detection | 11/21/1994 |
| SB 34-A134 |
|
en |
Mandatory Alert Navigation - RCA AVQ21 and Primus 40 Weather Radar Systems - Defective Mounting Tray for Receiver/Transmitter | 04/01/1978 |
| SB 34-A155 |
2 |
en |
Mandatory Alert Navigation - Windshear Detection and Recovery System - Inspection of Interface Between the Flap System and the Windshear Computer | 08/09/1995 |
| SB 34-JA 891143 |
|
en |
Mandatory Navigation - Introduction of Shortened Cable Looms to No. 1 and No. 2 Vertical Gyroscopes | 03/02/1990 |
| SB 49-23-(6525) |
5 |
en |
Mandatory Airborne Auxiliary Power - Introduction of a 275 amp Airfuse for APU Start Circuit Protection | 08/18/1981 |
| SB 49-32-(9210A) |
1 |
en |
Mandatory Airborne Auxiliary Power - To Introduce an APU to Aircraft Structure Bonding Link | 03/24/1986 |
| SB 49-37-25A253A&B |
|
en |
Mandatory Airborne Auxiliary Power - Ignition/Starting - To Provide Fuse Protection to Battery Supplies in Debris Zone | 10/28/1991 |
| SB 49-40 |
1 |
en |
Mandatory Airborne Auxiliary Power - Ignition and Starting - Inspection of Cable Terminals on APU Start Circuit | 03/17/1994 |
| SB 49-PM 4714 Part 2 (a)(d) |
1 |
en |
Airborne Auxiliary Power - To Introduce Overheat Detection in APU Tail Cone | 04/05/1971 |
| SB 51-A-PM 5830 |
Iss 4 |
en |
Mandatory Alert Structural Integrity Audit - Special Inspection Requirements for Long Term Operation (Supplemental Inspection Document) | 01/28/1993 |
| SB 52-89-00668H-L |
2 |
en |
Mandatory Doors - Passenger and Service Doors - To Introduce Stronger Springs on Passenger and Service Doors to Ensure Side Baulk Blade Retraction | 06/03/1991 |
| SB 52-A-JA 911140 |
2 |
en |
Mandatory Alert Doors - Inspection of Taper Pin on Passenger/Crew Door Locking Mechanism | 10/06/1992 |
| SB 52-A-JA 930901 |
1 |
en |
Mandatory Alert Doors - Passenger/Crew Door - Internal Door Handle Mounting Platform Structure Failure | 02/11/1994 |
| SB 52-A-JM 7704 |
|
en |
Mandatory Alert Doors: To Provide Retention of the Shouldered Bolt at the Upper Connection of the Passenger/Crew Door Restraint Cable | 11/17/1989 |
| SB 52-A-PM5448 |
Iss 2 |
en |
Mandatory Alert Rear Passenger Door - Cracks in Skins and Structures | 07/04/1977 |
| SB 52-JM 7752 |
|
en |
Mandatory Doors - Introduction of Improved Escape Hatch Shear Fitting | 12/17/1991 |
| SB 52-JM 7793 |
1 |
en |
Mandatory Doors - Passenger/Crew Door Introduction of Revised Microswitch Rigging and Drawbolt Penetration | 08/10/1993 |
| SB 53-59-(3031B) |
2 |
en |
Mandatory Fuselage - Reinforcement of Canopy Upper Rail | 01/08/1987 |
| SB 53-60 |
|
en |
Mandatory Fuselage - Pipe Installation - Possible Fouling | 11/08/1985 |
| SB 53-62-(3127) |
1 |
en |
Mandatory Fuselage - Ventral Tank Aft Attachment - Fuselage Keel Steel Fitting | 10/15/1986 |
| SB 53-63 |
|
en |
Mandatory Fuselage - Outer Skin - Introduction of Additional Inspection Requirements | 02/27/1987 |
| SB 53-65-3168A |
1 |
en |
Mandatory Fuselage - Nose Section - To Introduce Reinforcing Straps to Windscreen Centre Pillar | 03/09/1989 |
| SB 53-73 |
2 |
en |
Mandatory Fuselage - Inspection of Nose Landing Gear Bay Sidewall for Cracks | 05/18/1991 |
| SB 53-74-3193C&D |
|
en |
Mandatory Fuselage - Fairings - Introduction of Drain Masts at Rear Equipment Bay Vent Outlets | 01/07/1992 |
| SB 53-74-3193C&D |
1 |
en |
Mandatory Fuselage - Fairings - Introduction of Drain Masts at Rear Equipment Bay Vent Outlets | 03/12/1992 |
| SB 53-130 |
|
en |
Mandatory Fuselage - Centre Section - Inspection of Frame 29 for Possible Cracking in the Vicinity of Bolt Holes | 05/10/1994 |
| SB 53-131 |
|
en |
Mandatory Fuselage - Centre Section - Inspection of Frame 29 for Possible Cracking in the Vicinity of Bolt Holes | 03/29/1995 |
| SB 53-144 |
|
en |
Mandatory To Inspect for Skin Cracking in the Vicinity of Frame 29 Between Stringers 12 and 13 | 08/27/1998 |
| SB 53-144 |
1 |
en |
Mandatory To Inspect for Skin Cracking in the Vicinity of Frame 29 Between Stringers 12 and 13 | 05/21/1999 |
| SB 53-152 |
|
en |
Mandatory To Inspect for Cracking Along the Face of the Retraction Jack Attachment Boss in the Left Hand Nose Landing Gear Sidewall | 10/08/1998 |
| SB 53-152 |
8 |
en |
Mandatory To Inspect for Cracking Along the Face of the Retraction Jack Attachment Boss in the Left Hand Nose Landing Gear Sidewall | 02/19/2018 |
| SB 53-167 |
1 |
en |
Fuselage - Forward Fuselage External Inspections | 05/18/2004 |
| SB 53-167 |
4 |
en |
Fuselage - Forward Fuselage External Inspections | 06/10/2010 |
| SB 53-229 |
1 |
en |
To Inspect for Cracking in Stiffeners Adjacent to the NLG Retraction Jack Attachment Boss at the Left and Sidewall of the Nose Landing Gear Bay | 11/22/2010 |
| SB 53-239 |
3 |
en |
Fuselage - Inspection of Rear Fuselage Aft Skin Lap Joints for Cracking | 05/07/2014 |
| SB 53-239 |
5 |
en |
Fuselage - Inspection of Rear Fuselage Aft Skin Lap Joints for Cracking | 03/02/2017 |
| SB 53-249 |
|
en |
Fuselage - Centre Fuselage - to Inspect Forward Rib 0 Longeron | 08/25/2023 |
| SB 53-A-JA870510 |
1 |
en |
Mandatory Alert Fuselage - Inspection of NLG Retraction Jack Upper Mounting Fitting Securing Bolts | 11/10/1987 |
| SB 53-A-PM5922 |
|
en |
Mandatory Alert Fuselage Inspection Requirements for Extended Operations at Cabin Pressure Differential Up to a Maximum of 8.2 Pounds per Square Inch | 01/27/1987 |
| SB 53-A-PM5922 |
Iss 2 |
en |
Mandatory Alert Fuselage Inspection Requirements for Extended Operations at Cabin Pressure Differential Up to a Maximum of 8.2 Pounds per Square Inch | 04/27/1995 |
| SB 53-A-PM5989 |
|
en |
Mandatory Alert Fuselage, Forward Passenger and Service Door Aperture, Skin Cracking | 10/03/1991 |
| SB 53-A-PM5990 |
|
en |
Mandatory Alert Fuselage, Forward Pressure Floor Panel, Cracking of Skin and Cleats | 01/07/1991 |
| SB 53-A-PM5991 |
|
en |
Mandatory Fuselage - Cracks in Machined Attachment Angles and Auxiliary Beams on the Outboard Pressure Floor at Station 570 (670 for 500 Series) | 09/05/1990 |
| SB 53-A-PM5993 |
|
en |
Mandatory Alert Fuselage Frames at Stations 178 and 213.5 - Cracks at Floor Level Adjacent to Forward Passenger Doorway | 01/11/1993 |
| SB 53-A-PM5994 |
Iss 3 |
en |
Mandatory Alert Fuselage - Cracks in Structural Members in Flight Deck Canopy Area | 04/08/1993 |
| SB 53-A-PM5994 |
Iss 4 |
en |
Mandatory Alert Fuselage - Cracks in Structural Members in Flight Deck Canopy Area | 08/23/1996 |
| SB 53-A-PM5994 |
Iss 5 |
en |
Mandatory Alert Fuselage - Cracks in Structural Members in Flight Deck Canopy Area | 04/18/1997 |
| SB 53-A-PM6032 |
|
en |
Engine Mounting Beams - Cracking of Lugs | 04/07/1995 |
| SB 53-A-PM6035 |
|
en |
Mandatory Alert Cracks in Nose Landing Gear (NLG) Trunnion Fittings | 03/07/1996 |
| SB 53-A-PM6036 |
|
en |
Mandatory Alert Fuselage - Main Landing Gear A-Frame Attachment Fittings - Inspect for Cracks | 11/24/1995 |
| SB 53-JA-990842 |
1 |
en |
Mandatory Alert Fuselage - Inspection for Cracking on Rudder Quadrant Support Structure | 02/21/2000 |
| SB 53-JM5285 |
2 |
en |
Fuselage - Introduction of a Revised Attachment Bracket for the Nose Landing Gear Retraction Jack | 11/12/1992 |
| SB 53-JM7297 |
|
en |
Fuselage - To Introduce Additional Stringers, to Reinforce the Skin Panels Between Frame Stations 223 - 241.3 and 241.3 - 257.8 Below Stringers 142 Port and Starboard (Modification JM 7297) | 05/10/1984 |
| SB 53-PM3082 |
1 |
en |
Fuselage - To Revise the Main Chassis Door Jack Mounting Structure Situated on the Keel | 10/02/1967 |
| SB 54-10 |
|
en |
Pylons - Inspection of Pylon to Wing Forward Attachment Bolts, and Introduction of Lower Torque Valves and Sealant Under Bolt Heads and Nuts | 09/16/1999 |
| SB 55-014-01510A |
|
en |
Mandatory Stabilizers - Elevators - To Introduce a Revised Mass Balance Weight to the Leading Edge of the Horn | 12/15/1995 |
| SB 55-13-014908 |
|
en |
Mandatory Horizontal Stabilizers - To Introduce a Definitive Standard of Drain Holes in the Elevators | 07/07/1995 |
| SB 55-15 |
|
en |
Mandatory To Inspect Horizontal Stabilizer to Vertical Stabilizer Attachment Brackets for Corrosion | 04/14/1997 |
| SB 55-16 |
|
en |
Mandatory To Inspect Elevator Hinge Bracket Rib 1 for Cracking | 07/14/1997 |
| SB 55-A-JA-990640 |
|
en |
Mandatory Alert Inspection of Vertical Stabilizer Skins - Right and Left Hand Side | 09/01/1999 |
| SB 55-A-PM5827 |
Iss 2 |
en |
Mandatory Alert Corrosion and Cracks in Tailplane Lower Machined Skin | 09/05/1990 |
| SB 56-JA 920843 |
1 |
en |
Mandatory Windows - Inspection of Left and Right Pilots' Windscreens for Cracking of PVB Interlayer | 12/16/1993 |
| SB 57-072 |
3 |
en |
Mandatory Wing - Inspection of Wing Fixed Leading Edge and Front Spar Structure, Left and Right Wing | 08/31/2010 |
| SB 57-073 |
1 |
en |
Wings - Inspection of Forward Pylon Pick Up Fittings at Rib 10 | 01/27/2012 |
| SB 57-073 |
2 |
en |
Wings - Inspection of Forward Pylon Pick Up Fittings at Rib 10 | 03/08/2012 |
| SB 57-33 |
|
en |
Mandatory Wings - Root Joint Attachment Fittings - Rear Spar Root Joint Attachment Fittings at Wing Rib 2 | 08/31/1989 |
| SB 57-33 |
1 |
en |
Mandatory Wings - Root Joint Attachment Fittings - Rear Spar Root Joint Attachment Fittings at Wing Rib 2 | 10/29/1993 |
| SB 57-33 |
2 |
en |
Mandatory Wings - Root Joint Attachment Fittings - Rear Spar Root Joint Attachment Fittings at Wing Rib 2 | 02/16/1994 |
| SB 57-33 |
3 |
en |
Mandatory Wings - Root Joint Attachment Fittings - Rear Spar Root Joint Attachment Fittings at Wing Rib 2 | 09/16/1994 |
| SB 57-40 |
|
en |
Mandatory Wings - Inspection of Fastener Holes in the Butt Strap at Rib 2 Lower Wing Skin Joint | 03/18/1994 |
| SB 57-41 |
|
en |
Mandatory Wings - Centre Section - Inspection of Wing Top Skins at Rib '0' for Possible Cracking | 07/26/1991 |
| SB 57-47 |
|
en |
Mandatory Wings - Aileron Servo and Trim Tab Drive Brackets - Corrosion and Cracking | 06/15/1995 |
| SB 57-48 |
|
en |
Mandatory Wings - Aileron Servo and Trim Tab Drive Brackets - Corrosion and Cracking | 06/30/1995 |
| SB 57-49 |
|
en |
Mandatory Wings - Top Wing Skin Stress Corrosion Cracking | 06/04/1996 |
| SB 57-49 |
1 |
en |
Mandatory Wings - Top Wing Skin Stress Corrosion Cracking | 06/19/1997 |
| SB 57-50 |
2 |
en |
Mandatory Inspection for, and Application of Primer to, 'Drill Marked' Areas on the Underside of the Wing Top Skin Panels | 03/20/1997 |
| SB 57-54 |
1 |
en |
Mandatory Wings - Flap Outer Hinge Assembly - Cracking of Lug on Hinge Arm | 02/09/1978 |
| SB 57-55 |
|
en |
Mandatory To Inspect LH and RH Wing Bottom Skin Stringers for Machining into Stringer Web | 04/27/1998 |
| SB 57-55 |
2 |
en |
Mandatory Wings - Flap Outer Hinge Assembly - Inspection of Hinge Assemblies with Modification 252670 | 02/18/1992 |
| SB 57-56 |
|
en |
Mandatory To Inspect for Loose JO-Bolts and Fretting of Crown Fittings on All Stringers at Wing Rib 0 and Rib 2 Left Hand and Right Hand | 09/02/1999 |
| SB 57-58 |
4 |
en |
Mandatory Wings - Flaps - Possible Cracking of Nose Ribs at Outboard Hinges | 03/10/1984 |
| SB 57-66 |
2 |
en |
Mandatory Wings - Aileron Mass Balance - Possible Cracking of Side Plate Attachment Lugs | 10/25/1986 |
| SB 57-72 |
1 |
en |
Mandatory Wings - Possible in-Service Cracking of Main Landing Gear (MLG) Sidestay Attachment Lug | 09/28/1990 |
| SB 57-73 |
|
en |
Mandatory Wings - Possible Corrosion of Wing Top Skin Beneath Boundary Layer Fence | 07/30/1991 |
| SB 57-73 |
1 |
en |
Mandatory Wings - Possible Corrosion of Wing Top Skin Beneath Boundary Layer Fence | 05/29/1992 |
| SB 57-75 |
|
en |
Mandatory Wings - Inspection of Wing Top Skins for Cracks Around Countersunk Attachment Bolt Holes and Internal Stringers | 07/30/1991 |
| SB 57-76 |
|
en |
Mandatory Wings - Inspection of LH and RH Rear Spar and Outboard Main Landing Gear Support Bracket for Corrosion | 12/31/1991 |
| SB 57-A-JA 920540 |
|
en |
Alert Wings - To Introduce Revised Joggled Doublers in the Main Landing Gear Bay (LH and RH) | 09/01/1992 |
| SB 57-A-JA 920640 |
|
en |
Mandatory Alert Wings - Inspection for Migration of the Wing/Fuselage Forward Attachment Spigot Bushes | 02/19/1993 |
| SB 57-A-JA 980441 |
1 |
en |
Mandatory Alert Wings - Inspection of Main Landing Gear Bay Auxiliary Spar Structure | 07/07/1998 |
| SB 57-A-PM5992 |
|
en |
Mandatory Alert Wings - Cracks in Lower Surface and Leading Edge Fixed Ribs 6, 10 and 14 | 10/14/1992 |
| SB 57-JA 020740 |
2 |
en |
Wings - Inspection of Bolts at Wing Stub Spigot Post Assembly at Frame 199 | 11/02/2005 |
| SB 57-JA120141 |
1 |
en |
Inspection of Main Landing Gear Trunnion Cap Tension Bolts | 04/08/2014 |
| SB 57-JA140140 |
|
en |
Wings - Inspection of the Wing Main Spar Around Rib 36 | 06/26/2014 |
| SB 57-JA 921140 |
1 |
en |
Mandatory Wings - Inspection and Introduction of Special Nut to Mounting Spigots in the Aileron Control System | 02/03/1994 |
| SB 57-JA 921144 |
|
en |
Mandatory Wings - Inspection of the Spigot Housing Plate at the Wing/Fuselage Forward Attachment Sliding Joint and Introduction of a New Modified Spigot and Spigot Housing Plate | 03/04/1993 |
| SB 57-JA 921144 |
1 |
en |
Mandatory Wings - Inspection of the Spigot Housing Plate at the Wing/Fuselage Forward Attachment Sliding Joint and Introduction of a New Modified Spigot and Spigot Housing Plate | 04/19/1994 |
| SB 57-JA 921144 |
2 |
en |
Mandatory Wings - Inspection of the Spigot Housing Plate at the Wing/Fuselage Forward Attachment Sliding Joint and Introduction of a New Modified Spigot and Spigot Housing Plate | 05/26/1997 |
| SB 57-JA 930941 |
2 |
en |
Mandatory Wings - Inspection of the Spigot Housing Plate at the Wing/Fuselage Forward-Attachment Sliding-Joint | 11/11/1994 |
| SB 57-JM5218 |
4 |
en |
Wings - To Introduce Main Landing Gear Fitting Part Number 1379133B1 and B2 | 10/31/1990 |
| SB 57-JM5218 |
5 |
en |
Wings - To Introduce Main Landing Gear Fitting Part Number 1379133B1 and B2 | 07/28/1997 |
| SB 57-JM5221 |
|
en |
Wings - Re-Inforcement of the Bottom Wing Skin at the Landing Gear Bay Cutout at Wing Station 115 | 09/28/1984 |
| SB 57-JM5259 (w/Err 1) |
|
en |
Wings - Introduction of Modified Bushes at the Wing/Fuselage Forward Attachment Spigots | 02/05/1993 |
| SB 57-JM5326 |
|
en |
Wings - Wing/Fuselage Forward Attachment - To Introduce New Modified Spigots | 09/03/1993 |
| SB 57-JM7298 |
|
en |
Wings, Bonding - To Introduce a Bonding Point at Station 297 Port and Starboard (Modification JM 7298 Part A) | 05/16/1984 |
| SB 57-JM8160 |
1 |
en |
Mandatory Wings - Introduction of Cold Worked Holes at Main Spar Access Panel Attachments | 08/23/1991 |
| SB 71-68-01581A |
1 |
en |
Power Plant - To Introduce Inner Skin Dishing to LH Side Inner Surface of Rear Cowling Doors to Clear Repositioned Engine Anti-Ice Pipe, Introduced by Allied Signal Service Bulletin ALF/LF72-1020 | 03/25/1998 |
| SB 74-JM 7693A |
3 |
en |
Mandatory Ignition - Introduction of Auto-Relight Magnetic Latching Relays (LH & RH) | 01/28/1993 |
| SB 76-A-JA910542 |
|
en |
Mandatory Alert Engine Controls - Life Limitations of Power Lever Control Cables | 05/30/1991 |
| SB 76-A-PM6031 |
|
en |
Mandatory Alert Engine Controls - Failure of Thrust Reverse Control Cables in Stub Wing | 01/18/1995 |
| SB 76-A-PM6043 |
|
en |
Mandatory Alert Reverse Thrust - Rigging Check of Control Pulleys | 09/18/1998 |
| SB 76-PM2837 |
1 |
en |
Mandatory Engine Controls - To Redesign Plunger Unit of Reverse Thrust Selection Mechanism in Throttle Handles | 04/10/1967 |
| SB 78-4-9949A |
|
en |
Mandatory Exhaust - Dee Howard Thrust Reversers - Introduction of Countersunk Headed Bolts at the Thrust Reverser Door Hinge Pivot | 01/20/1992 |
| SB 78-PM6047 |
1 |
en |
Mandatory Thrust Reverser - Introduction of a Combined Selector Sequence Valve with Revised Locking Spring and Spring Sleeve Rolls Royce Spey Modification 6426 (Service Bulletin Sp78-133) | 11/27/1998 |
| SB 80-2-(1533) |
4 |
en |
Starting - Cracking - Introduce Optional Use of Fanned Starter/Generators for Aircraft with Viper 521 or 522 Engines Fitted | 03/27/1979 |
| SB 80-8 |
|
en |
Starting- Engine Start H.P. Cock Microswitches - Unsatisfactory Engagement of Operating Roller on Cam Profile | 01/18/1978 |
| SB 80-8-(2656) |
|
en |
Starting- Engine Start H.P. Cock Microswitches - Improve Operation of H.P. Cock Microswitches in Throttle Box | 05/22/1978 |
| SB 80-A-JA 911045 |
1 |
en |
Mandatory Alert Engine Control - Introduction of Additional Post Flight Procedure and Removal of Diodes from Engine Stop Circuit | 11/01/1991 |
| SB A-ATP-32-26 |
1 |
en |
Alert Landing Gear - Inspection of Normal Operating Linkage and Operational Test of the Auxiliary System | 09/25/1990 |
| SB ATP-21-24-10306A |
|
en |
Mandatory Air Conditioning - ECS Fan Control - Introduction of Genelco Circuit Breaker Part No. 4330-014-10 | 07/30/1993 |
| SB ATP-21-36 |
|
en |
Mandatory Air Conditioning - ECS - Inspection of the Ram Air Inlet Ducts | 01/03/1996 |
| SB ATP-23-21-35288A |
2 |
en |
Mandatory Communications - To Prevent Loss of Communications Following a Fault on Ground Crew Jackbox or PA Handset | 02/15/1994 |
| SB ATP-23-21-35288A |
Err 2 |
en |
Mandatory Communications - To Prevent Loss of Communications Following a Fault on Ground Crew Jackbox or PA Handset | 04/25/1994 |
| SB ATP-24-34 |
|
en |
Mandatory Electrical Power - To Reduce Standby Compass Deviation Errors by: Introducing Modified Earthing Arrangements to the Pitot Static and Stall Warning System & Introducing Modified Earthing Arrangements to the Overhead Stowage Units | 04/25/1991 |
| SB ATP-24-38-10204A |
2 |
en |
Alert Electrical Power - To Increase the Cable Size of the Stall Warning Heating Circuits to Reduce the Voltage Drop, and of the Stall Warning Lift Transducer to Cater for Increased Wattage Heaters | 08/14/1991 |
| SB ATP-24-42-10244A |
1 |
en |
Mandatory Electrical Power - To De-Activate Alternative Three-Phase Supply to Transformer Rectifier Units | 11/07/1991 |
| SB ATP-24-45-35229A |
|
en |
Mandatory Electrical Power - Introduction of Bonding Leads to the Throttle Stepper Motor Controller, the Oil Cooler Temperature Controller in Module 3 and the Engine De-Ice Timers | 12/20/1991 |
| SB ATP-24-49-10247A |
1 |
en |
Mandatory Electrical Power - Introduction of Leach Contractor (Type Half-002) in Lieu of Cutler Hammer Contractor (Type SM15-CX-A6 or A8) in the TRU Power Supply Changeover Circuit | 10/23/1992 |
| SB ATP-24-55 |
1 |
en |
Mandatory Electrical Power - To Ensure the Integrity of the Bonding of Module 3 Via the Throttle Stepper Motor Controller (Stepper Motor Drive Unit) | 04/24/1993 |
| SB ATP-26-016 |
|
en |
Inspection of Fire Bottles for Excessive Solder between Operating Head and Container | 10/04/2011 |
| SB ATP-26-5-35225A |
|
en |
Mandatory Fire Protection - Engine - Introduction of ICC Fire Detector at the Intercompressor Case | 10/30/1991 |
| SB ATP-26-9 |
|
en |
Mandatory Fire Protection - Introduction of a Once Only Safety Ohmmeter Check to Ensure the Integrity of the Engine Fire Extinguisher Circuits at the Cartridge Connectors | 05/12/1993 |
| SB ATP-27-090 |
|
en |
Flight Controls - Inspection of Aileron and Rudder Tab Piano Hinges for Hinge Pin Security | 04/14/2009 |
| SB ATP-27-41-70031B |
3 |
en |
Mandatory Flight Controls - Introduction of Stall Warning Lift Transducer Part No. C74007-4 in Lieu of Existing Units Part No. C74007-2 or C74007-3 | 06/05/1992 |
| SB ATP-27-49-10234A |
1 |
en |
Mandatory Flying Controls - Minor Wiring Change to Obviate an Uncommanded Elevator Split Being Generated by a Single (Stray-Earth) Fault | 08/14/1993 |
| SB ATP-27-49-10234A |
2 |
en |
Mandatory Flying Controls - Minor Wiring Change to Obviate an Uncommanded Elevator Split Being Generated by a Single (Stray-Earth) Fault | 11/23/1993 |
| SB ATP-27-55 |
|
en |
Mandatory Flight Controls - Introduction of a Once Only Inspection of the Gearbox/Primary Flap Drive Torque Tube Splined Flanged-Coupling Bolts at STN "0" for Security of Attachment | 08/14/1992 |
| SB ATP-27-78 |
1 |
en |
Mandatory Flight Controls - Introduction of Improvements to the Flight Control Installation | 01/31/1996 |
| SB ATP-27-80 |
|
en |
Mandatory Flight Controls - Inspection for Adequate Clearance Around Flap Torque Tubes | 04/23/1996 |
| SB ATP-27-86 |
|
en |
Mandatory Flying Controls - Inspection of Bolt Orientation at Rudder Primary Drive Rod and Synchro Drive Rod Ends | 05/15/1999 |
| SB ATP-29-12-10392A |
|
en |
Mandatory Hydraulics - Introduction of Revised Piping to the Auxiliary Reservoir Supply and Brake Pressure Bleed System. Removal of the Landing Gear Bypass Pipeline and Fitting of Additional Non Return Valve in the Main Pressure System, with Revised Flight Manual Procedures | 09/09/1995 |
| SB ATP-29-15 |
|
en |
Mandatory Hydraulic Power - Inspection of the Main Hydraulic Accumulator for Corrosion | 02/25/1997 |
| SB ATP-30-056 |
|
en |
Mandatory Ice and Rain Protection - Engine Intake De-Icing System - Installation of Intake Ducts with New Cable Routes and Improved Contamination Protection (Left and Right) | 06/11/1999 |
| SB ATP-30-3 |
3 |
en |
Mandatory Ice and Rain Protection - Windscreen and Window Rain Repellent | 10/19/1990 |
| SB ATP-30-10 |
|
en |
Mandatory Ice and Rain Protection - Improvements of the Washer System and Repositioning Windscreen Washer Nozzles | 09/30/1991 |
| SB ATP-30-10 |
1 |
en |
Mandatory Ice and Rain Protection - Improvements of the Washer System and Repositioning Windscreen Washer Nozzles | 02/24/1992 |
| SB ATP-30-13 |
1 |
en |
Ice and Rain Protection - Introduction of a New Propeller Digital Ice Control Timer Unit Part No. 790112-5 in Lieu of Part No. 790112-4D and a New Propeller Blade Assembly Type ABA811-001 in Lieu of Type ABA810-48 | 02/15/1991 |
| SB ATP-30-20-10248A&C |
1 |
en |
Mandatory Ice and Rain Protection - Introduction of Electrical Power Filters and Fixed Fittings into Main and Side Windscreen Heating Systems (Pre-Mod 10106A 200 Volt Windscreens) | 02/17/1992 |
| SB ATP-30-30-35285A |
|
en |
Ice and Rain Protection - Introduction of a Time Delay in the Right Hand Engine Intake De-Icing System | 07/15/1994 |
| SB ATP-30-37-30143A |
|
en |
Mandatory Ice and Rain Protection - Introduction of Wiring Changes to Allow Flexible Intake Duct, to be Powered Automatically with Engine Air Intake Lip | 08/01/1994 |
| SB ATP-30-37-30143A |
1 |
en |
Mandatory Ice and Rain Protection - Introduction of Wiring Changes to Allow Flexible Intake Duct, to be Powered Automatically with Engine Air Intake Lip | 09/05/1994 |
| SB ATP-30-39-30146A |
|
en |
Mandatory Introduction of Engine De-Ice Timers AC69116-13 and AE20628-13 | 07/29/1994 |
| SB ATP-30-44-35274D |
|
en |
Ice and Rain Protection - Introduction of Engine Duct De-Ice Overheat Protection | 08/12/1994 |
| SB ATP-32-29 |
1 |
en |
Mandatory Landing Gear - Introduction of Two New Swivel Assemblies, A Restricting Collar and a Protection Cover for the Emergency Undercarriage Release Mechanism | 06/06/1991 |
| SB ATP-32-30 |
2 |
en |
Mandatory Landing Gear - Inspection and Modification of the Normal Selector Mechanism | 04/22/1991 |
| SB ATP-32-30 |
3 |
en |
Mandatory Landing Gear - Inspection and Modification of the Normal Selector Mechanism | 05/20/1991 |
| SB ATP-32-33 |
|
en |
Mandatory Landing Gear - To Introduce the Requirements of Dowty Aerospace Gloucester Service Bulletin 200-32-143 | 03/01/1991 |
| SB ATP-32-37 |
|
en |
Mandatory Landing Gear - To Introduce a Once Only Inspection of the Nose Wheel Steering Quadrant and the Upper Steering Control Toggle Link Assembly | 02/14/1992 |
| SB ATP-32-48 |
1 |
en |
Mandatory Landing Gear - Main Wheel - Failure of Main Wheel Bearing in Service | 01/28/1994 |
| SB ATP-32-48 |
3 |
en |
Mandatory Landing Gear - Main Wheel - Failure of Main Wheel Bearing in Service | 07/15/1994 |
| SB ATP-32-51-35296A |
|
en |
Landing Gear - Main Landing Gear - Improved Adjustment of the Wheel Bearing Pre Load | 05/12/1994 |
| SB ATP-32-53-35294A |
|
en |
Mandatory Landing Gear - Main Wheel - Introduction of Main Wheels AHA2120 and AHA2122 in Lieu and by Conversion of Main Wheel AHA1663 | 07/18/1994 |
| SB ATP-32-53-35294A |
2 |
en |
Mandatory Landing Gear - Main Wheel - Introduction of Main Wheels AHA2120 and AHA2122 in Lieu and by Conversion of Main Wheel AHA1663 | 01/13/1995 |
| SB ATP-32-53-35294A |
Err 1 |
en |
Mandatory Landing Gear - Main Wheel - Introduction of Main Wheels AHA2120 and AHA2122 in Lieu and by Conversion of Main Wheel AHA1663 | 07/19/1994 |
| SB ATP-32-80 |
1 |
en |
Mandatory Landing Gear - Brakes - Hydraulic Power - Inspection of the Brake Hydraulic Accumulators for Corrosion | 07/09/1997 |
| SB ATP-32-84 |
1 |
en |
Mandatory Doors - Main Landing Gear Doors - Inspection of the Main Landing Gear Forward Door Mechanism | 09/26/1997 |
| SB ATP-32-87 |
|
en |
Mandatory Main Landing Gear - Forward Door Mechanism - Installation of a New Spring Strut (Left and Right) | 01/29/1998 |
| SB ATP-32-93 |
1 |
en |
Mandatory Nose Landing Gear - Replacement of Weight on Wheels Microswitch Harness Sub-Assembly | 08/02/1999 |
| SB ATP-32-99 |
|
en |
Mandatory Landing Gear - Main - Inspection of the Torque Links Apex Joint Assembly (Left and Right) | 02/21/2000 |
| SB ATP-33-8 |
2 |
en |
Lighting - To Revise Roof and Sidewall Light Wiring to Reduce E2B Standby Compass Deviations | 04/11/1991 |
| SB ATP-33-19-10238A |
|
en |
Mandatory Lights - Moving Cabin Lighting from Essential to Non Essential Circuit to Alleviate Potential Exceeding the Battery Capacity on Introduction of Stall Warning Heater Mod 70031B | 03/19/1992 |
| SB ATP-34-40 |
|
en |
Navigation - To Highlight the Requirements of Smiths Industries Mandatory Service Bulletin 1205AM-34-756 to Embody Mod 02 to Altimeter Repeater Units Pt. No. 1205AM1 | 10/20/1990 |
| SB ATP-52-26-10350B |
|
en |
Mandatory Repair to Class One Doors to Prevent Shoot-Bolt Bush Migration | 06/29/1994 |
| SB ATP-53-10 |
|
en |
Fuselage Structure - Introduction of Improved Ice Protection from Propeller Ice Impact | 03/07/1990 |
| SB ATP-53-29 |
|
en |
Mandatory Fuselage - Door Apertures - Inspect Gussets for Cracks and Corrosion | 10/31/1994 |
| SB ATP-53-30-10372A |
|
en |
Mandatory Fuselage - Nose Landing Gear - To Introduce and Inspection of the Nose Landing Gear Retraction Actuator Bracket Attachment Assembly and to Repair/Replace as Required | 11/03/1994 |
| SB ATP-53-31 |
1 |
en |
Mandatory Inspection for Corrosion on External Antenna Reinforcing Plates | 12/05/1995 |
| SB ATP-53-36 |
1 |
en |
Mandatory Structure - Inspection of Nose Landing Gear Down Lock, Bulkhead 378FS and the Adjacent Structure | 02/21/2000 |
| SB ATP-54-9 |
|
en |
Mandatory Nacelles - To Introduce Redefined Fatigue Lives and an Inspection of the Bolts Attaching the LH and RH Aft Isolator Brackets to the Engine Subframe Aft Mounting Beams | 12/09/1992 |
| SB ATP-54-10-35256A |
1 |
en |
Nacelle - Engine Change Unit - Introduction of Improved Fasteners Attaching the Engine Aft Isolator Brackets to the Engine Mounting Beams | 04/16/1993 |
| SB ATP-54-11 |
|
en |
Mandatory To Introduce Inspection of the Quick Engine Change Unit (QECU) Subframe Yoke | 07/13/1993 |
| SB ATP-54-11 |
1 |
en |
Mandatory To Introduce Inspection of the Quick Engine Change Unit (QECU) Subframe Yoke | 11/09/1993 |
| SB ATP-54-12-35274A |
|
en |
Mandatory Nacelles - Debris Duct Assembly - Introduction of an Eductor Plate | 09/28/1993 |
| SB ATP-54-12-35274A |
1 |
en |
Mandatory Nacelles - Debris Duct Assembly - Introduction of an Eductor Plate | 12/15/1993 |
| SB ATP-54-13-35274B |
|
en |
Mandatory Nacelles - Introduction of Improved Engine Air Intake | 10/09/1993 |
| SB ATP-54-13-35274B |
1 |
en |
Mandatory Nacelles - Introduction of Improved Engine Air Intake | 07/08/1994 |
| SB ATP-54-13-35274B |
2 |
en |
Mandatory Nacelles - Introduction of Improved Engine Air Intake | 08/18/1994 |
| SB ATP-54-14 |
|
en |
Nacelles - Engine Air Intake - To Introduce an Inspection of the Heater Mats (Dunlop Part No. ACA2016) | 10/14/1993 |
| SB ATP-55-3 |
4 |
en |
Mandatory Stabilizers - To Introduce an Inspection of the Rudder Lower Hinge Attachment Brackets and the Attachments of Reinforcing Plates and Bearing Housings | 06/28/1990 |
| SB ATP-55-5 |
|
en |
Strengthening of Rudder Lower Hinge Ribs at Stations 29.582, 27.582 and 24.82 | 11/30/1990 |
| SB ATP-55-5 |
1 |
en |
Strengthening of Rudder Lower Hinge Ribs at Stations 29.582, 27.582 and 24.82 | 01/03/1991 |
| SB ATP-57-13 |
1 |
en |
Mandatory Wings - Inspection for Cracks in the Aft End of the Outboard Engine Rib Boom Angles | 01/15/1993 |
| SB ATP-57-13 |
5 |
en |
Mandatory Wings - Inspection for Cracks in the Aft End of the Outboard Engine Rib Boom Angles | 06/03/1994 |
| SB ATP-57-14 |
1 |
en |
Mandatory To Introduce an Inspection Check of the Wing Top Surface Stringer Joint Bolts | 09/27/1993 |
| SB ATP-57-14 |
3 |
en |
Mandatory To Introduce an Inspection Check of the Wing Top Surface Stringer Joint Bolts | 12/15/1993 |
| SB ATP-57-16-10313A |
1 |
en |
Wings - Introduction of Modified Engine Rib Boom Angles | 07/02/1994 |
| SB ATP-61-2 |
1 |
en |
Mandatory Propellers - Introduction of Application of ICEX or Autoglyn No. 12 to Each Propeller Blade when Operating in Icing Conditions | 10/31/1989 |
| SB ATP-61-2 |
2 |
en |
Mandatory Propellers - Introduction of Application of ICEX or Autoglyn No. 12 to Each Propeller Blade when Operating in Icing Conditions | 10/25/1990 |
| SB ATP-61-2 |
3 |
en |
Mandatory Propellers - Introduction of Application of ICEX or Autoglyn No. 12 to Each Propeller Blade when Operating in Icing Conditions | 04/19/1991 |
| SB ATP-71-15 |
|
en |
Power Plant General - Engine Drains - To Prevent Possible Chafe Damage of the Hose for the Fuel Manifold Drain (FD1) | 12/11/1998 |
| SB ATP-76-16 |
|
en |
Mandatory Inspection of Engine Power Cables for Excess Wear/Damage | 10/14/1994 |
| SB ATP-76-18 |
|
en |
Engine Controls - Introduction of Increased Diameter Pulley Assembly to Engine Power Control Cable Circuit | 06/21/1995 |
| SB ATP-79-23 |
|
en |
Mandatory Cracking of Engine Air Cooled Oil Cooler | 08/26/1994 |
| SB ATP-79-24-10360A |
|
en |
Introduction of an Improved Engine Air Cooled Oil Cooler | 09/04/1994 |
| SB ATP-79-25-10382A |
1 |
en |
Mandatory Oil - Introduction of Modified Oil Filter Differential Pressure Switch Airframe Wiring | 05/25/1995 |
| SB ATP-80-06 |
1 |
en |
Mandatory Introduction of a Life Limitation for the Engine Igniter Plugs and Staggered Replacement Period to Improve Ignition Reliability | 10/22/1993 |
| SB ATP-80-06 |
2 |
en |
Mandatory Introduction of a Life Limitation for the Engine Igniter Plugs and Staggered Replacement Period to Improve Ignition Reliability | 10/16/1994 |
| SB ATP-80-7-30141A |
2 |
en |
Starting - Introduction of an Auto-Ignition System | 11/04/1994 |
| SB ATP-A32-85 |
1 |
en |
Mandatory Alert Main Landing Gear - Forward Door Mechanism - Inspection of the Spring Strut for Looseness of the Fork End (Left and Right) | 03/20/1998 |
| SB ATP-A32-94 |
|
en |
Mandatory Alert Landing Gear - Nose Landing Gear - Introduction of Steering Compensator Serviceability Tests | 10/03/1998 |
| SB ATP-A52-30 |
|
en |
Mandatory Alert Doors - Front and Rear Passenger and Rear Baggage Door - Inspection of Door Handle Operating Shafts | 03/19/1997 |
| SB ATP-A71-14 |
|
en |
Mandatory Alert Power Plant - Drainage - Chafe Damage to a Fire Skin Access Panel and Fuel Drain Hose in Module 2 of the Nacelle | 11/04/1998 |
| SB ATP/J61-32-71 |
1 |
en |
Mandatory Landing Gear - Wheels and Brakes - Brake Unit Part No. AHA1612 and AHA2004 - Introduction of Inspection and Procedure to Find and to Set the Corrected Wear Remaining Length of the Wear Indicator Pin | 06/18/1996 |
| SB B121/79 |
1 |
en |
Mandatory Crack Propagation to the Port and Starboard Wing Spar Webs Immediately Outboard of the Root Rib | 02/15/1991 |
| SB B121/94 |
|
en |
Alert Rudder Controls - Incorrect Assembly | 05/31/1988 |
| SB B121/95 |
2 |
en |
Mandatory Flying Controls - Failure of Handgrip Fitting on Control Column | 01/28/1991 |
| SB B121/105 |
|
en |
Mandatory Fuselage - To Introduce Inspections at the Main Spar | 01/12/1998 |
| SB B121/106 |
|
en |
Mandatory Mainplanes - To Introduce New Nuts at the Wing to Fuselage Main-Spar Attachment Fittings | 01/12/1998 |
| SB D49205-33-01 |
|
en |
Mandatory 100VA Dimmer Unit - Correction of Possible Internal Short Circuit | 04/14/1989 |
| SB HS748-27-63 |
4 |
en |
Mandatory Flight Controls - Introduction of Aileron Cable Support Block Under the Crew Compartment Floor | 05/12/1995 |
| SB HS748-27-70 |
2 |
en |
Mandatory Flight Controls - Introduction of a Modified Aileron Cable Pulley Guard at Station 314, 366 and Rubbing Strips at Ribs 34.071, 43.071 and 52.071 on the Port Side and Ribs 251.366 and 260.366 on the Starboard Side | 05/20/1994 |
| SB HS748-27-124 |
|
en |
Mandatory Flying Controls - Aileron Operating Arm Bracket Failure | 11/17/1995 |
| SB HS748-27-126 |
|
en |
Mandatory Flight Controls - Inspection of Cable Tension Regulators, Gust Locks and Cable Pressure Seals | 02/29/1996 |
| SB HS748-27-136 |
|
en |
Flight Controls - Inspection of Rudder and Aileron Tab Piano Hinges for Hinge Pin Security | 04/14/2009 |
| SB HS748-29-49 |
|
en |
Mandatory Hydraulic Power - Inspection of the Main Hydraulic Accumulators for Corrosion | 02/25/1997 |
| SB HS748-53-59-INSP |
|
en |
Mandatory Nose Landing Gear - Inspection/Rectification of Retraction Jack Mounting Bracket Bearing Cap Fasteners | 05/04/1994 |
| SB HS748-A27-128 |
|
en |
Mandatory Alert Flight Controls - Control System Gust Locks | 12/20/1996 |
| SB HS758-29-49 |
|
en |
Mandatory Hydraulic Power - Inspection of the Main Hydraulic Accumulators for Corrosion | 02/25/1997 |
| SB J41-11-004 |
1 |
en |
Mandatory Placards and Markings - Interior Placards - Introduction of a Placard at the Elevator Decouple Control Handle | 03/23/1994 |
| SB J41-11-007 |
|
en |
Mandatory Placards - Main Entrance Door - Position of Door Open Internal Placards | 05/10/1995 |
| SB J41-11-010 |
|
en |
Mandatory Placards and Markings - Main Baggage Compartment - Introduction of Reduced Loading Limitations | 08/09/1997 |
| SB J41-11-014 |
|
en |
Mandatory Placards - Main Baggage Bay - Introduction of New Weight Limitations | 01/18/1996 |
| SB J41-11-020 |
|
en |
Mandatory Placards and Markings - Introduction of Warning Label for Rear Baggage Bay Fire Extinguisher | 11/10/1997 |
| SB J41-22-006 |
|
en |
Mandatory Autoflight - Autopilot - Installation of Circuit Breakers to Prevent an Overheat Failure of the Flight Control Computer | 07/01/1996 |
| SB J41-24-027 |
|
en |
Mandatory Electrical Power - Introduction of Improved Sealing to Electrical Connectors on Rear Pressure Bulkhead Area | 07/08/1997 |
| SB J41-24-027 |
Err 1 |
en |
Mandatory Electrical Power - Introduction of Improved Sealing to Electrical Connectors on Rear Pressure Bulkhead Area | 08/08/1997 |
| SB J41-24-033 |
2 |
en |
Mandatory Electrical Power - DC Generation - Overheat Failure of Earth Posts (Left and Right) | 01/24/1996 |
| SB J41-24-043 |
3 |
en |
Electrical Power- DC Generation- Overheat Failure of Earth Posts (Left and Right) | 06/16/2014 |
| SB J41-25-018 |
|
en |
Mandatory Equipment/Furnishing - Introduction of Decompression Vents in the Left and Right Forward Stowage and the Forward Right Wardrobe Assembly | 03/15/1994 |
| SB J41-25-068 |
|
en |
Mandatory Equipment/Furnishings - Bulkhead Assembly - Installation of a Revised Decompression Panel | 11/09/1995 |
| SB J41-26-008 |
2 |
en |
Fire Protection - Re-Orientation of Fire Extinguisher in the Toilet Vanity Unit and Introduction of Replacement Unit | 09/20/2011 |
| SB J41-26-009 |
|
en |
Fire Protection - Engine Fire Extinguisher Cartridge - Connector Spacer Integrity | 11/23/2016 |
| SB J41-27-027 |
|
en |
Flying Controls - Aileron - Installation of a New Bearing in the Aileron Quadrant (Left and Right) | 01/17/1994 |
| SB J41-27-036 |
|
en |
Mandatory Flight Controls - Aileron and Elevator Disconnect - Travel Stop Migration in the Control Handles | 09/02/1994 |
| SB J41-27-052 |
|
en |
Mandatory Flight Controls - Strengthening of Elevator and Rudder Controls at the Rear Pressure Bulkhead | 09/11/1998 |
| SB J41-27-059 |
|
en |
Mandatory Flying Controls - Introduction of an Elevator Cable Tension Regulator Incorporating Secondary Locking of the Regulator Input Lever | 05/31/2000 |
| SB J41-27-068 |
|
en |
Flight Controls - Inspection of Elevator Trim Circuit Travel Stops and Servo Motor Limit Micro Switch Rigging | 01/21/2014 |
| SB J41-28-010 |
1 |
en |
Mandatory Fuel - Distribution - Protection of the Cable Assembly to the Fuel Standby (Boost) Pump (Left and Right) | 09/07/1999 |
| SB J41-28-013 |
2 |
en |
Fuel - Introduction of Additional Bonding Leads between Pipes, Structures & Various Components within Fuel Tank Areas | 07/08/2019 |
| SB J41-29-001 |
|
en |
Mandatory Hydraulic Power - Spoiler System - Installation of New Bleed Nipples at the Retract and Extend Connections of the Actuator | 08/12/1994 |
| SB J41-29-001 |
1 |
en |
Mandatory Hydraulic Power - Spoiler System - Installation of New Bleed Nipples at the Retract and Extend Connections of the Actuator | 08/30/1994 |
| SB J41-29-005 |
1 |
en |
Mandatory Hydraulics Case Drain - Introduction of Additional Fairlead Support and Revised Material for Case Drain Line in Engine/Nacelle Rear Spar Support | 08/12/1994 |
| SB J41-29-005 |
2 |
en |
Mandatory Hydraulics Case Drain - Introduction of Additional Fairlead Support and Revised Material for Case Drain Line in Engine/Nacelle Rear Spar Support | 08/30/1994 |
| SB J41-32-017 |
|
en |
Mandatory Landing Gear - Introduction of Main Landing Gear Crashworthy Trunnion Pins | 02/07/1994 |
| SB J41-32-023 |
|
en |
Mandatory Landing Gear - Main Gear - Replacement Pins for Shock Strut and Drag Brace | 05/27/1996 |
| SB J41-32-044 |
|
en |
Mandatory Landing Gear - Landing Gear Control - Installation of a New Landing Gear Control Unit and Revised Wiring | 09/22/1995 |
| SB J41-32-049 |
1 |
en |
Mandatory Landing Gear - MLG - Drag Brace - Inspect Upper Link | 01/15/1996 |
| SB J41-32-054 |
|
en |
Mandatory Landing Gear - Main Gear - Replacement Bolts for Shock Strut | 07/04/1996 |
| SB J41-32-058 |
|
en |
Mandatory Landing Gear - Main Wheel - Tie Bolts - Introduction of Revised Maintenance Instructions and Line Requirements | 05/09/1997 |
| SB J41-51-001 |
4 |
en |
Structures - Introduction of New and Revised Inspections for Fatigue and Environmental Damage | 07/11/2017 |
| SB J41-52-025 |
|
en |
Doors - Passenger/Crew Door - Introduction of Improved Door Handrail Assembly | 02/11/1994 |
| SB J41-52-041 |
|
en |
Doors - Main Entrance-Door - Interim Reinforcement of the Handrail Assembly | 06/13/1994 |
| SB J41-52-050 |
|
en |
Doors - Passenger Door - Introduction of Strengthened Passenger Door Roller Guides | 05/06/1997 |
| SB J41-52-058 |
|
en |
Doors - Passenger Door - Lubrication of 'G' Lock and Speed Lock Systems | 07/14/1997 |
| SB J41-52-060 |
|
en |
Mandatory Doors - Cargo Doors - Inspection of the Mounting Structure for the Bottom Rollers of the Main Baggage-Bay Door, and Inspection of the Door Counter-Balance Mechanism | 08/31/1998 |
| SB J41-52-064 |
|
en |
Doors - Introduction of Ultrasonic Inspection of the Upper and Lower Passenger/Crew Door Pin Guides | 09/15/2009 |
| SB J41-52-065 |
1 |
en |
Doors - Inspection of Passenger Door Inner Skin, Edge Member & Seal Carrier Adjacent to Roller Brackets | 06/08/2022 |
| SB J41-53-011 |
|
en |
Mandatory Fuselage - Forward Section - Reinforcement of the Aileron Drive Quadrant Support Structure Below the Flight Compartment Floor | 10/15/1993 |
| SB J41-53-012 |
|
en |
Mandatory Fuselage - Structure - Reinforcing of the Mounting Structure of the Elevator Controls on Rear Pressure Bulkhead | 11/30/1993 |
| SB J41-53-012-41262A |
1 |
en |
Mandatory Fuselage - Structure - Reinforcing of the Mounting Structure of the Elevator Controls on Rear Pressure Bulkhead | 10/03/1994 |
| SB J41-53-014 |
|
en |
Mandatory Fuselage - Introduction of Revised Type II Exit Surround Structure | 07/24/1995 |
| SB J41-53-014 |
1 |
en |
Mandatory Fuselage - Introduction of Revised Type II Exit Surround Structure | 02/09/1996 |
| SB J41-53-020 |
1 |
en |
Mandatory Fuselage - Rear Pressure Bulkhead Repair | 06/04/1996 |
| SB J41-53-028 |
1 |
en |
Mandatory Alert Fuselage - Aerodynamic Fairings - Flexural Cracks and Damage to the Overwing Fairing (Left and Right) | 10/12/1994 |
| SB J41-53-039 |
|
en |
Mandatory Fuselage - Replacement of Stringer Joint Piece Part No. 14153014-95 at Station 130 | 08/22/1996 |
| SB J41-53-041 |
|
en |
Mandatory Fuselage - Nose Wheel Bay Structure - Introduction of Additional Side Plates to Uplock Attachments | 07/25/1997 |
| SB J41-53-046 |
|
en |
Mandatory Fuselage - Introduction of 'D' Packers to Hydraulic Hand Pump Mounting Brackets | 03/15/2000 |
| SB J41-55-002 |
1 |
en |
Mandatory Stabilizers - Tailplane - Failure of Weather Seals Between the Tailplane and Fin | 07/25/1996 |
| SB J41-57-003 |
|
en |
Mandatory Electrical Power - Wing Rear Spar Harness - Introduction of Addition Clipping Point | 10/13/1993 |
| SB J41-57-017 |
|
en |
Wings - Flaps - Installation of New Structure for the Attachment of the Flap Nacelle Fairing (Left and Right) | 05/09/1997 |
| SB J41-57-021 |
|
en |
Wings - Replacement of the Wing Upper Splice Plate Part No. 14157126-3 | 05/07/1998 |
| SB J41-73-007 |
|
en |
Mandatory Engine Fuel and Control - Indicating - Installation of a New Pressure Switch in the Fuel Filter Blockage System. Left and Right | 11/22/1994 |
| SB J41-76-013 |
|
en |
Mandatory Engine Controls - Power and Condition Controls - Installation of Revised Flexible Control Cables (Left and Right) | 05/05/1995 |
| SB J41-A22-005 |
|
en |
Mandatory Alert Autoflight - Autopilot - Overheat Failure of the Flight Control Computer | 07/01/1996 |
| SB J41-A22-008 |
1 |
en |
Mandatory Alert Auto Flight - Elevator Trim Servo - To Inspect for Loose Motor Housing | 11/21/1996 |
| SB J41-A24-012 |
1 |
en |
Mandatory Alert Electrical Power - DC Generation - Earth Post Failure | 09/13/1993 |
| SB J41-A24-036 |
|
en |
Mandatory Alert Electrical Power - DC Starter Generator - Bearing Failure | 02/26/1996 |
| SB J41-A25-034 |
1 |
en |
Mandatory Alert Equipment/Furnishings - Introduction of Foreign Object and Debris Guard to Rear Cabin Attendant Seat | 10/30/1993 |
| SB J41-A25-061 |
|
en |
Mandatory Alert Equipment/Furnishings - Passenger Seats - To Replace Seat Belt Shackles | 06/06/1995 |
| SB J41-A26-007 |
|
en |
Mandatory Alert Fire Protection - Engine and Nacelle Fire-Extinguisher System - To Find and Replace Possibly Defective Hoses in the System | 12/13/1996 |
| SB J41-A26-007 |
1 |
en |
Mandatory Alert Fire Protection - Engine and Nacelle Fire-Extinguisher System - To Find and Replace Possibly Defective Hoses in the System | 05/21/1997 |
| SB J41-A27-020 |
|
en |
Mandatory Alert Light Controls - Aileron Tab - Positive Locking of Hinge Wire | 08/13/1993 |
| SB J41-A27-026 |
1 |
en |
Mandatory Alert Flying Controls - Aileron - Inspection of Aileron Quadrant Bearing | 12/07/1993 |
| SB J41-A27-026 |
2 |
en |
Mandatory Alert Flying Controls - Aileron - Inspection of Aileron Quadrant Bearing | 01/17/1994 |
| SB J41-A27-034 |
|
en |
Mandatory Alert Flying Controls - Spoiler System - Inspection of Spoiler Actuators and Introduction of Revised System Flushing and Bleeding Procedure | 06/09/1994 |
| SB J41-A27-034 |
1 |
en |
Mandatory Alert Flying Controls - Spoiler System - Inspection of Spoiler Actuators and Introduction of Revised System Flushing and Bleeding Procedure | 10/28/1994 |
| SB J41-A27-042 |
|
en |
Mandatory Alert Flight Controls - Aileron System - Failure of the Aileron Disconnect Control System to Disconnect | 05/13/1996 |
| SB J41-A27-053 |
|
en |
Mandatory Alert Flying Controls - Inspection of Elevator Cable Tension Regulator Lever | 09/14/1999 |
| SB J41-A27-055 |
|
en |
Mandatory Alert Flight Controls - Rudder Pedals - Elimination of Potential Restricted Movement of the Rudder Pedals | 03/10/2000 |
| SB J41-A32-042 |
|
en |
Mandatory Alert Landing Gear - Landing Gear Control - Introduction of Wiring Changes to Prevent Uncommanded Retraction of the Landing Gear | 04/13/1995 |
| SB J41-A32-061 |
|
en |
Mandatory Alert Landing Gear - Main - Loose Spherical Bearings in the Lower Link of the Drag Brace | 07/11/1997 |
| SB J41-A52-016 |
|
en |
Mandatory Alert Doors - Main Baggage-Bay Door - To Inspect the Door Pressure Seal | 05/18/1993 |
| SB J41-A52-021 |
|
en |
Mandatory Alert Doors - Passenger/Crew - Inspection of the Electrical Loom of the Main Entrance Door for Damage and Its Subsequent Re-Routing Clear of the Speedlock Solenoid and the Inner Skin of the Door | 08/24/1993 |
| SB J41-A52-036 |
|
en |
Mandatory Alert Doors - Main Entrance-Door - Inspection for Cracks on the Handrail Assembly | 06/13/1994 |
| SB J41-A52-043 |
2 |
en |
Mandatory Alert Doors - Passenger Door - Inspection of Roller Guide Shear Cleats | 05/06/1997 |
| SB J41-A52-059 |
|
en |
Mandatory Alert Doors - Passenger Door - Introduction of Increased Diameter 'G' Lock Rollers | 09/12/1997 |
| SB J41-A52-059 |
2 |
en |
Mandatory Alert Doors - Passenger Door - Introduction of Increased Diameter 'G' Lock Rollers | 01/23/1998 |
| SB J41-A53-023 |
|
en |
Mandatory Alert Fuselage - Forward Fuselage - Inspection for Cracks in Diaphragms Installed Between Stn 4 and Stn 8 | 12/02/1996 |
| SB J41-A53-023 |
1 |
en |
Mandatory Alert Fuselage - Forward Fuselage - Inspection for Cracks in Diaphragms Installed Between Stn 4 and Stn 8 | 07/30/1999 |
| SB J41-A53-024 |
|
en |
Mandatory Alert Fuselage - Center Fuselage - Cracks on Frame 179 at the Attachment Bracket for the Door Restraint Cable | 04/26/1996 |
| SB J41-A53-028 |
2 |
en |
Mandatory Alert Fuselage - Aerodynamic Fairings - Flexural Cracks and Damage to the Overwing Fairing (Left and Right) | 01/17/1995 |
| SB J41-A53-030 |
|
en |
Mandatory Alert Fuselage - Floors - Installation of an Incorrect Intercostal in the Floor Structure of the Flight Compartment | 01/19/1996 |
| SB J41-A53-030 |
1 |
en |
Mandatory Alert Fuselage - Floors - Installation of an Incorrect Intercostal in the Floor Structure of the Flight Compartment | 08/08/1996 |
| SB J41-A53-030 |
2 |
en |
Mandatory Alert Fuselage - Floors - Installation of an Incorrect Intercostal in the Floor Structure of the Flight Compartment | 02/14/1997 |
| SB J41-A53-058 |
|
en |
Alert Fuselage - Frame 90 Reduced Inspection Interval | 12/06/2016 |
| SB J41-A57-015 |
1 |
en |
Mandatory Alert Wings - Flaps - Failure of Structure for the Attachment of the Flap Nacelle Fairing | 08/23/1996 |
| SB J41-A57-015 |
2 |
en |
Mandatory Alert Wings - Flaps - Failure of Structure for the Attachment of the Flap Nacelle Fairing | 06/30/1997 |
| SB J41-A57-029 |
|
en |
Alert Wings - Inspection of Rear Spar for Cracking | 05/06/2011 |
| SB J41-A57-029 |
3 |
en |
Alert Wings - Inspection of Rear Spar for Cracking | 04/08/2014 |
