The Aviation DataBase: Service Information: Hawker Beechcraft Service Instructions
The Aviation DataBase®
Complete Aviation Regulatory Library
Sept. 11 Sept. 11
DataBases updated: Nov 11th, 2025
Home Products Library Support Account Login Contact
Service Instructions
NameRevisionLangSubjectDate
en Electrical, Relocation of Regulator Field & Alternator Out Relay Fuses01/01/1968
en Fuel Selector Panel, Reroute Wiring01/01/1968
en Pressurization Supercharger, Modified Induction Air System01/01/1968
en Cabin Door, Installation of a Third Latch Point03/01/1968
en Take-Off Procedures with Minimum Fuel Supply06/01/1968
1 en Take-Off Procedures with Minimum Fuel Supply12/01/1968
en Cold Weather Procedures03/01/1968
en Pump Engine Driven, Installation of Heat Shield02/01/1968
1 en Induction System, Installation of New Air Filter Retainers06/01/1968
en Vacuum Oil Separator - Addition of Reinforcement Clamp02/01/1968
en Inlet Air Box - Sealing Corner Openings02/01/1968
en Compressor Drive - Installation of New Drive Seals02/01/1968
en Propeller Governor - Icing Protection for Control Rod02/01/1968
en Batteries - Installing G.E. Nickel Cadmium02/01/1968
en Baggage Door - Replacement of Hold-Open Assembly on Nose02/01/1968
en Rudder Pedal - Installation to Improve Brake Action02/01/1968
1 en Cabin Door (Folding Step) - Installation of Locking Mechanism11/01/1968
en Horizontal Stabilizer - Installing Chemical Milled Skins in Place of Original Skins02/01/1968
en Brake - Guided Piston Kit02/01/1968
1 en Conditioned Air - Accumulation of Water in Plenum Chamber05/01/1969
en Valves - Improved Outflow and Safety02/01/1968
en Power Plant - Installation of New Screws on McCauley Propellers02/01/1968
1 en Propeller - 2-Bladed and 3-Bladed - Part I: McCauley Service Bulletin No. 92, Cylinder Attachment Improvement (Attached); Part II: McCauley Service Bulletin No. 93, Counterweight Attachment Improvement (Attached)09/01/1971
1 en Propeller - 2-Bladed and 3-Bladed - Part I: McCauley Service Bulletin No. 92, Cylinder Attachment Improvement (Attached); Part II: McCauley Service Bulletin No. 93, Counterweight Attachment Improvement (Attached)09/01/1971
1 en Power Plant - Ordering Engine Mounts08/01/1968
en Landing Gear - Change of Paint on Strut, Steering and Retract Mechanisms02/01/1968
en Nose Gear - Addition of Rubber Bumper02/01/1968
en Landing Gear Retract Mechanism - Inspection of Uplock02/01/1968
1 en Propeller, Reversing, Installation of Proximity Switch & Sensor for Secondary Low Pitch Propeller Stop10/01/1968
en Induction System - Simplification03/01/1968
en Instruments - Replacement of Engine Gages04/01/1968
en Heater and Ignitor - New Heater Spark Plug02/01/1968
en Cowling - Improved Rods for Doors05/01/1968
en Power Plant - Reduction of Propeller Diameter03/01/1968
en Heat and Vent - Installation of Control Relay and Rewiring of Control Box03/01/1968
en Cowling (Aft) - Application of New Seal Cement to Oil Cooler Scoop Seals03/01/1968
en Oil System - Improved Plumbing04/01/1968
en Rudder Controls - Inspection of Cable Routing03/01/1968
en Seats (Passenger) - Installation of Arm Rest06/01/1968
en Emergency Extension - Inspection of Cable Routing Landing Gear03/01/1968
en Wing Front Spar - Use of Proper Wrench on Nut for Lower Forward Attachment Bolt04/01/1968
1 en Exhaust System - Installation of Heat Muff05/01/1968
en Fuel Transfer Pump - Correct Wiring for Control Transistors03/01/1968
1 en Fuselage - Inspection of Forward Wing Attach Point07/01/1974
2 en Fuselage - Inspection of Forward Wing Attach Point11/01/1979
en Cabin Door - Installation of Locking Mechanism04/01/1968
en Pressurization - Rework of Outflow Valve04/01/1968
en Power Plant - Installation of Exhaust Heat Shield05/01/1968
en Electrical System - Relocate Starting Vibrator Circuit04/01/1968
en Fuel System (Engine Section) - Inspection and Rework of Fireshield for Oil-to-Fuel Heater05/01/1968
en Instrument Panel - Inspection Beechcraft Turn Coordinator04/01/1968
1 en Pressure System (Instrument) - Replacement of Air Filters10/01/1968
1 en Pressure System (Instrument) - Replacing Dual Instrument Air Pressure Indicator11/01/1968
en Seats (Special) - Replacement of Seat Belt for Sixth Seat09/01/1968
en Electrical - (Wing and Engine Section) - Inspection of Fire Detection Harness04/01/1968
en Stabilator and Tab - Addition of Drain Holes06/01/1968
en Exhaust System - Removal of Vanes from Exhaust Stacks05/01/1968
en Electrical (Cockpit) - Inspection of Wiring to Overvoltage Relay05/01/1968
en Fuel Injection System - Inspection of Nozzle Assembly on Bendix RS-10FB1 System05/01/1968
en Electrical (Cockpit) - Rewiring Heater Circuit Breakers05/01/1968
en Electrical (Wing and Engine Section) - Inspection of Starter Relay and Mounting Clamps05/01/1968
en Oxygen System - Inspection of Oxygen Plumbing Behind Righthand Sidewall Instrument Panel05/01/1968
en Starter/Generator - Proper Installation of Lear Siegler Models Using Mounting Adapters05/01/1968
en Placards (Exterior) - Installation of Oil Dipstick Warning05/01/1968
en Engine Controls - Inspection of Routing and Clamping of Cables in Cabin Area12/01/1968
1 en Center Section - Reinforcement of Rear Spar Jack Pad12/01/1968
en Power Plant- Installation of New Bolt and Washer on Generator/Alternator Adjustment Arm05/01/1968
2 en Induction System - Installing a New Hinge Assembly on Inertial Separator Vane and Improving Vane Rigging01/01/1969
en Pitot and Static System - Improved Static Air Fittings06/01/1968
en Cabin Door - Improvement of Snubber Installation07/01/1968
en Exhaust System - Changing Clamp on Turbocharger/Exhaust Connection09/01/1968
en Electrical (Wing and Engine Section) - Servicing of Magneto and EGT Wiring04/01/1969
en Power Plant - Replacement of Cowl Flap Actuator and Bracket07/01/1968
en Brakes - Change to Soft Linings for Better Wear Characteristics06/01/1968
en Subpanel - Installation of New Circuit Breaker for Cigarette Lighter06/01/1968
en Power Plant - Washing PT6 Engine Compressor06/01/1968
1 en Special Tools - Calibration Equipment for TIT Indicator System03/01/1978
1 en Pressure System (Instrument) - Installation of Shield on Inlet Filter02/01/1969
2 en Horizontal Stabilizers - Checking Alignment of Elevator Hinge Brackets and Inspecting Horizontal Stabilizer Skin for Cracks06/01/1969
en Rudder Tab - Addition of Drain Holes07/01/1968
en Electrical - - Use of Adequate Ground Power Supplies for Engine Starting07/01/1968
en Engine Controls - Cable Routing and Support08/01/1968
1 en Placards (Exterior) - Retrofit of Exterior Decal-Type Emblems12/01/1968
en Heater Installation - Modification to Prevent Fuse Burn-Out During Normal Operation09/01/1968
2 en Induction System - Installing Seal Strips and a Spring Assembly on Internal Separator Vane12/01/1968
1 en Power Plant - Installation of Improved Voltage Regulator06/01/1972
en Empennage Installation - Inspection of Horizontal Stabilizer Skins, Elevator Skins & Torque Tube Collars08/01/1968
en Electrical (Fuselage Section) - Rerouting Lower Rotating Beacon Wire Harness08/01/1968
1 en Instruments - Replacing Fuel Flow Indicator07/01/1969
en Main Gear Actuator - Installation of Brake Assembly08/01/1968
en Fuel System - Engine Section - Replacing Engine Primer Solenoid Valves & Fuel Heater Solenoid Valves10/01/1968
en Brake Master Cylinder - Modification of VHR625NL Master Cylinder (Pilots) to Obtain Clearance for Left Parking Brake Valve Actuating Arm09/01/1968
1 en Empennage Installation - Addition of Rivets in Elevator and Inspection of Rivets in Rudder and Stabilizers09/01/1969
en Nacelle and Side Brace Ribs (Center Section) - Installation of Side Brace Rib Doublers09/01/1968
en General - FAA Approval Status of Beech Publications08/01/1968
en Heater Installation - Inspecting Hanlon and Wilson, (P/N 8046-1), Heater-Muffler for Cracks08/01/1968
1 en Electrical (Cockpit and Nose Section) - Inspection of Co-Palum Terminals on 150 Ampere Air Conditioner Power Circuit Breaker10/01/1968
en Cabin Door - Installation of Lock with Screw-Held Cam08/01/1968
en Seats (Passenger) - Rework of Seat Reclining Mechanism09/01/1968
en Control Wheel - Clock and Map Lite - Emblem and Clock Mounting Modification10/01/1968
1 en Rudder and Tab - Reinforcement of Rudder Spar in Hinge Bracket Area05/01/1969
en Fire Detection - Rework to Prevent False Fire Indication09/01/1968
en Fuel System (Engine Section) - Reroute Fuel Line to Simplify Oil Filter Removal09/01/1968
en Heater Installation - Addition of Gasket Under Fuel Nozzle09/01/1968
en Power Plant - Installation of Oil Filter on Lycoming Engine09/01/1968
en Electrical (Cockpit and Nose Section) - Improved Fuel Flow Inverter Protection09/01/1968
en Fuel System - Rerouting Nacelle Gravity Feed Fuel Lines11/01/1968
1 en Nacelle & Fillets (Wing) - Inspecting & Strengthening Nacelle Installation02/01/1969
en Cowling - Modification to Split Nose Cowl11/01/1968
en Main Gear Assembly - Addition of Longer Bushings at Main Gear Attachment Points09/01/1968
en Electrical - Addition of Resistor to Alternator Out Relay Circuit09/01/1968
en Electrical - Rerouting of Auxiliary Power Lead Wire10/01/1968
en Center Section Assembly - Reinforcement of External Power Plug Bracket10/01/1968
en Power Plant - Addition of Auto-Ignition System10/01/1968
1 en General - Removal of King Air Flight Restrictions11/01/1968
en Main Gear Installation - Reinforcement of Up-Position Indicator Switch Bracket11/01/1968
en Nose Gear Wheel - Installation of Improved Nose Wheel Centering Cable11/01/1968
en Cowling (Forward) - Installation of Engine Cowl Nose Bug Tie Plate09/01/1969
1 en Pressure System - Modification, Inspection and Adjustment02/01/1970
1 en Electrical - Modification to Prevent Inadvertent Tripping of Flap Circuit Breaker10/01/1969
en Placards (Interior) - Temporary Limitation of Slow Roll Manuevers10/01/1968
en Cabin Door - (Folding Step) - Addition of Dual Support Cable11/01/1968
en Nose Cone and Tail Cone - Installation of Protective Plastic Nose Cone Cap11/01/1968
en Instruments - Calibration of TIT Indicator10/01/1968
1 en Pressure System (Instrument) - Replacement of Air Filters03/01/1969
en Front Spar Carry-thru Structure - Enlarging Flap Motor Access Hole11/01/1968
1 en Windshield - Checking for & Preventing Windshield Delamination04/01/1970
1 en Engine Controls - Inspecting and Rigging Throttle Control04/01/1969
en Empennage - Addition of Rivets in Horizontal Stabilizer and Elevator11/01/1968
en Main Gear Installation - Replacement of Drag Link Assembly Down Lock Hook Pins11/01/1968
en Fuel Selector Panel and Controls - Installation of Fuel Tank Selection Placard
en Pressurization Controller - Outflow and Safety Valves - "Soft-Mount Installation"02/01/1969
1 en Electrical (Wing and Engine Section) - Installation of Starter and Battery Relay Covers03/01/1969
en Heater Installation - Modification of Fuel and Air Feed Assembly11/01/1968
1 en Landing Gear - Installation of New Grease Seal Assemblies on Goodrich Wheels05/01/1969
en Empennage Installation - Installation of Radius Fillers & Longer Bolts01/01/1969
en Baggage Compartment Doors (Forward) - Installation of Caution Decals12/01/1968
en Placards (Interior) - Operation of Aircraft without Utility Doors02/01/1969
en Elevator Tab Actuator - Inspection of Rivets in Mounting Nutplates12/01/1968
en Conditioned Air - Addition of Pressure Relief Valve, Improvement of Overpressure Switch Circuit & Reduction of Freon System Pressure12/17/1968
en Power Plant - Inspection of Constant Speed Propeller Installation12/01/1968
en Electrical (Wing and Engine Section) - Rerouting & Clamping of Wire Bundle to Reverse Current Diodes01/01/1969
en Fuel System (Engine Section) - Inspection of Fuel Flow Transmitter01/01/1969
en Placards (Exterior) - Inverter Cooling Duct Warning02/01/1969
1 en Placards (Interior) - Installation of a Caution Plate on Pilot's Air & Light Escutcheon03/01/1969
en Heater Installation - Rerouting of Heat and Vent Ducting01/01/1969
en Pressurization - Improvements & Modifications in System06/01/1969
1 en Fuselage - Modification of Fuselage Drain Provisions09/01/1969
en Nose Gear Steering - Installation of Shroud to Cover Nose Gear Steering Actuator Drive Assembly05/01/1969
en Pitot and Static System - Securing Static Air Valve Knob01/01/1969
en Center Section Leading Edge - Reinspection for Security & Condition of Components
3 en Empennage - Elevator - Inspection of Torque Tube Assembly Collar and Control Horn Assembly for Wear and Fatigue Cracks09/01/1972
en Nacelle - Addition of Improved Access to Wing Ice Lights02/01/1969
1 en Cowling (Aft) - Modification of Oil Cooler Scoop Fasteners01/01/1972
1 en Power Plant - Magneto Ignition Harness Improvement12/01/1969
en Electrical (Wing and Engine Section) - Ignition Harness Improvement02/01/1969
en Electrical (Cabin Section) - Replacement of Generator Control Panel Cover Assembly02/01/1969
en General - Description and Operation of Alternator System02/01/1969
en Electrical (Wing and Engine Section) - Modification of Starter Generator Control Circuit04/01/1969
en Induction System - Installing a Larger Flex Boot on Inertial Separation Vane Control Linkage03/01/1969
1 en Cowling (Aft) - Modification of Oil Cooler Scoop Fasteners01/01/1972
en Wing Tip - Installation of New Strobe Light Glareshield03/01/1969
1 en Power Plant - Induction System - Inspection of Flexible Air Ducts08/01/1971
en General - Addition of Protective Coating on Fiberglass Parts02/01/1969
en Horizontal Stabilizer - Spares Replacement02/01/1969
en Cabin Furnishings - New Armrests for First Four Seats07/01/1969
1 en Empennage Installation - Inspecting Lower Rudder Hinge Assembly05/01/1969
en Electrical (Wing and Engine Section) - Inspection of Generator Fault Relay Wiring02/01/1969
en Horizontal Stabilizer - Replacement of Horizontal Stabilizer Actuator03/01/1969
en Placards (Interior) - Revision of Max. Structural Cruise Speed and Never Exceed Speed02/01/1969
en Pressurization Plumbing and Ducts - Cleaning Flow Control Valve Solenoid Valve Screen & Rerouting Ram Air Door Latch Wiring08/01/1969
en Fuel System - Sealing & Pressure Testing Fuel Tank Vent Assemblies02/01/1969
en Landing Gear - Safetying Up & Down Indicator Switches02/01/1969
en Placards (Exterior) - Installation of Engine Oil Placard02/01/1969
en Induction System - Improved Carburetor Air Box Assembly04/01/1969
en Electrical (Fuselage Section) - Installation of Alternator Out Sensor05/01/1969
en Fuel Selector Valve - Inspection to Insure Proper Shutoff03/01/1969
en Landing Gear - Inspection of Actuators03/01/1969
en Battery Installation - Strengthening of Nose Mounted Battery Carrier05/01/1969
1 en Power Plant - Installation of Prestolite Alternators in Place of Delco-Remy Alternators04/01/1971
en Nose Gear Doors - Rigging Improvement03/01/1969
en Assist Step - Replacement of Shear Rivet in Retract Cable Actuator Arm03/01/1969
en Elevator & Tab Controls - Replacement of Bolts03/01/1969
en Main Gear Doors - Inspection of Tire Clearance to Main Gear Inboard Doors05/01/1969
en Power Plant - Inspecting Fuel Hose Firesleeves and Installing Oil Line Firesleeving06/01/1969
en Elevator - Inspecting for, and Repairing, Cracks in Spar at Outboard Hinge Bracket03/01/1969
en Electrical - Voltage Regulator Adjustment06/01/1969
en Electrical (Wing & Engine Section) - Prevention of Diode Burn Out03/01/1969
en Battery Installation - Servicing General Electric Nickel-Cadmium Batteries with Sonotone PCA131 Battery Charger/Analyzer04/01/1969
en Landing Gear Retract Mechanism - Reworking Nose Gear Drag Brace Support04/01/1969
en Electrical (Wing & Engine Section) - Capping A5 Connector04/01/1969
en Heater Installation - Rework for Improvement04/01/1969
en Fire Extinguisher - Engine - Replacing Hose Assembly04/01/1969
1 en Pressurization Plumbing & Ducts - Temporary Restriction on Operation of Intercooler Control06/01/1969
en Electrical (Engine Section) - Improving Ignition Harness Installation05/01/1969
en Nacelle & Fillets (Wing) - Installation of New Wing Fillets05/01/1969
1 en Main Gear Assembly - Sealing to Prevent Corrosion & Inspection for Cracks05/01/1971
1 en Electrical (Cockpit and Nose Section) - Spraycoating Cockpit Printed Circuit Boards03/01/1970
2 en Electrical (Cockpit and Nose Section) - Spraycoating Cockpit Printed Circuit Boards04/01/1970
en Main Gear Doors - Replacing Outboard Gear Door Hinge Assemblies07/01/1969
en Exhaust System - Inspection & Maintenance of Turbocharger Wastegate Butterfly06/01/1969
en Pressurization Plumbing & Ducts - Modification of Firewall Shutoff Valve08/01/1969
en Compressor - Inspection of Hydraulic Reservoir Supercharger Drive System Vent06/01/1969
en Nose Gear Assembly - Inspection for Corrosion09/01/1970
en Power Plant - Replacing Carburetor07/01/1969
2 en Main Gear Installation - Extension & Retraction - Inspection of Actuator Clevis & Drag Leg Clevis Bolt11/01/1972
1 en Landing Gear - Replacement of Tie Bolts on Goodrich Wheels09/01/1969
en Landing Gear - Modification of Goodyear Wheels for Use with Tube Types Tires or Rim Inflated Tubeless Tires06/01/1969
1 en Electrical (Wing & Engine Section) - Changing Wire Terminals at Generator/Alternator02/01/1970
en Power Plant - Inspection & Rework of Propeller Overspeed Governor06/01/1969
en Battery Installation - Adding Extra Vent Holes to Battery Cell Vent Spray Caps07/01/1969
en Fuel Pump - Engine Driven - Modification of Filter Screen Flow Passage & Replacement of Coupling Retaining Ring09/01/1969
en Instrument Panel Plumbing - Inspection & Reworking Pressure Manifold06/01/1969
en Wing Box Section - Cutting an Access Hole06/01/1969
en Heater Fuel Plumbing - Replacing a Check Valve with a Ball Valve07/01/1969
en Nose Structure - Sealing Baggage Compartment08/01/1969
en Aileron & Aileron Tab Controls - Adding a Nut to Aileron Control Rod End07/01/1969
en Fuel System - Modification to Permit Slow Roll Maneuver07/01/1969
1 en Placards (Interior) - Inspection of Fuel Selector Valve Cover Plate01/01/1970
en Pressure System (Instrument) - Modification of Pressure Pump Shroud07/01/1969
en Power Plant - Rerouting of Starter-Generator Air Cooling Duct07/01/1969
en Cowling - Installing a Divider Vane in Induction System Intake Duct08/01/1969
en Rudder Pedals & Linkage - Inspection of Pilots LH Rudder Pedal Linkage Arm07/01/1969
en Seats (Copilot) - Relocation of Copilots Seat Recline Control Handle07/01/1969
en Nacelle & Side Brace Ribs (Center Section) - Installing a Wheel Well Ice Protection Boot10/01/1969
3 en Heater Installation - Improvement01/01/1976
en Flight Controls - Inspection of Tab Control Push-Pull Tubes07/01/1969
en Pressurization - Operation of System07/01/1969
1 en Elevator - Inspection & Replacement of Torque Tube03/01/1970
1 en Pressurization System - Installation of Improved Safety & Outflow Valves09/01/1972
en Placards (Interior) - Adding a Fuel Selector & Takeoff & Landing Decal07/01/1969
en Electrical (Fuselage Section) - Installing Chafe Strips for Wing Stub Terminal Boards07/01/1969
en Cabin Door - Securing Latch Pin Cable Housings07/01/1969
1 en H-14 Autopilot - Inspection of Aileron Servo Cables & Rigging06/01/1973
3 en Wing Skins - Inspecting Wings & Flaps for Corrosion Aft of Exhaust Stack01/01/1971
en Electrical (Wing & Engine Section) - Applying a Protective Coating to Flap Control Potentiometer07/01/1969
en Electrical (Cockpit & Nose Section) - Insulating Terminals on Main & Standby Trim Relays in Pedestal07/01/1969
en Fuselage - Modification to Help Prevent Moisture Leaks08/01/1969
1 en Fuel Systems (Fuel Selector Valve) - Installation of Indicator on Fuel System12/01/1972
en Landing Gear - Main Gear Assembly - Addition of Loctite to Landing Gear Torque Knee Bushings08/01/1969
en Cowling - Adding a Doubler to Oil Filler Door Opening08/01/1969
en Fuel System - Inspection of Fuel Return Line10/01/1969
en Horizontal Stabilizer - Inspection of Elevator Hinge Fittings08/01/1969
en Electrical (Fuselage Section) - Adding One Ampere Fuses to Fuel Flow Indicator Inverter Circuit09/01/1969
en Control Wheel - Clock and Map Light - Relocating Trim Release Switch and Installation of Control Wheel Cap10/01/1969
en Nacelle (Center Section) -Venting 120 Volt/Ampere Inverter08/01/1969
2 en Pedestal Controls - Replacing Idle Control Catch Plate06/01/1970
en Aileron and Aileron Tab Controls - Installation of an Improved Aileron Centering Cable08/01/1969
4 en Control Wheel - Clock and Map Light - Replacing Control Wheel Adapter05/01/1972
en Pressure System (Instrument) - Replacing Air Filter & Adding Tubing Support Clamps08/01/1969
en Main Gear Installation - Inspection of Main Landing Gear Drag Brace Bolts09/01/1969
1 en Pressure System - Inspecting Clamping of Pneumatic Pressure Regulator Valves & Lines12/01/1969
en Crew Compartment Structure (Lower) - Installation of Protective Cover Over Electrical Components08/01/1969
en Brakes - Adjuster Spring Inspection09/01/1969
en Pedestal & Console Structure - Providing Clearance between Pedestal & Instrument Floating Panel09/01/1969
en Fuselage Structure (Aft) - Installation of Reinforcement Angle09/01/1970
en Fuel System - Nacelle Fuel Tank Indicator Light09/01/1969
en Front Spar Carry thru Structure - Rework Spar Stiffeners to Provide Clearance for Landing Gear Retract Rod Pressure Boots09/01/1969
en Baggage Compartment (FWD) - Rework of Lock Body Assembly Retaining Nut & Tumbler Retaining Screw09/01/1969
en Pressure System (Instrument) - Installing Pressure Failure Indicator09/01/1969
en Control Wheel - Increase Grip Friction09/01/1969
en Electrical (Cockpit & Nose Section) - Adjustment or Replacement of Heater Overtemperature Switch09/01/1970
en Electrical (Cabin Section) - Replacing Current Limiters09/01/1969
1 en Aft Fuselage - Modification of Drain Provisions04/01/1970
en Control Wheel - Clock & Map Light - Insulating Splices on Coiled Cord Wire09/01/1969
1 en Electrical - Addition of Pitch Trim Warning System and Modification of Standby Trim Switches10/01/1969
en Electrical (Wing & Engine Section) - Heated Stall Warning Switch10/01/1969
en Instrument Panel (Floating) - Re-Marking Engine Gage12/01/1969
en Landing Gear Retract Mechanism - Rework of Uplock Arm10/01/1969
en Instrument Panel - Installation of an Improved Cabin Heat Control Cable Assembly08/01/1970
1 en Placards (Interior) - Installation of a Horizontal Stabilizer Actuator Duty Cycle Definition & Instructions Placards10/01/1969
en Surface Deicer - Addition of Firesleeve to Deicer Poly-Flo Line10/01/1969
en Main Landing Gear Doors - Removal of Seals10/01/1970
1 en Landing Gear Retract Mechanism - Replacement or Modification of Main Gear Retract Rods05/01/1971
en Control Wheel - Modification of Control Wheel Switches10/01/1969
en Horizontal Stabilizer - Inspection of Bonding on Trailing Edge Skins10/01/1969
en Pressurization Plumbing & Ducts - Installing a Righthand Bleed Air Supplemental Heating System10/01/1969
en Cowling (Forward) - Flushing Anti-Ice Inertial Vane Control Cables02/01/1970
en Cabin Door - Shortening Spring Under Pressure Lock Defeat Handle10/01/1969
1 en Cabin Door - Replacement of Latch Clevis Pin with Bolt01/01/1970
en Control Wheel - Clock & Map Light Relocating Trim Release Switch Installation of Control Wheel Cap & Replacing Standby Trim Switches12/01/1969
en Horizontal Stabilizer - Modification of Horizontal Stabilizer Cap Attaching Strap10/01/1969
en Battery Installation - Inspecting Battery Case Vent Tube11/01/1969
en Battery Installation - Application of Corrosion Preventive Compound on Battery Relay Diodes11/01/1969
2 en Pitot and Static System - Modification of Primary and Alternate Static Air System04/01/1972
en Electrical - Inspection for Proper Location of Fuel Control Air-Line Heater Ground11/01/1969
en Landing Gear Retract Mechanism - Inspection of Nose Gear Torque Shaft for Proper Alignment & Excessive End Play11/01/1969
en Placards (Interior) - Installation of a Horizontal Stabilizer Actuator Duty Cycle Definition & Instructions Placard11/01/1969
1 en Instrument Panel (Fixed) - Tachometer Modification03/01/1970
1 en Instrument Panel (Floating) - Installation of Electric Gyros on Pilots Instrument Panel12/01/1969
en Placards (Interior) - Replacing Battery & Alternator Switch Identification Plate11/01/1969
en Electrical (Wing & Engine Section) - Replacement of External Power Solenoid11/01/1969
en Subpanel - Installation of Landing Gear Switch Guard12/01/1969
en Propeller (2-Bladed) - Inspection and Replacement of Pitch Control Bolts and Yoke11/01/1969
en Induction System - Inspection and/or Replacement of Main and Alternate Air Valve Assembly11/01/1969
en Fuel System (Engine Section) - Draining and Flushing of Marvel-Schebler Carburetors11/01/1969
1 en Electric Trim Installation - Procedural Steps for Modification of Horizontal Stabilizer Up Travel Limit and Flight Checking Trim Position12/01/1969
en Landing Gear - Replacement of Circuit Breaker and Wires11/01/1969
en Pedestal Controls - Adjustment of Landing Gear Warning Horn Switches01/01/1970
en Electrical - Modification of Landing Gear Control Circuit01/01/1970
en Brake Plumbing - Installation of Brake Fluid Reservoir with Check Valve and Overboard Drain02/01/1970
1 en Pedestal Controls - Replacing Flap Control Switch Plate04/01/1972
en Power Plant - Replacing Turbocharger Oil Line03/01/1970
2 en Stabilizers - Replacement of Elevators and Reinforcement of Elevator Hinge Brackets02/01/1982
3 en Flight Controls - Inspection of Elevator Control Push Rods09/01/1978
4 en Horizontal Stabilizer Replacement of Inboard Elevator Hinge Bracket04/01/1975
en Seats (Passenger) - Replacing Seat Track Attach Screws in Rear Spar Cap03/01/1970
1 en Seats (Passenger) - Replacing Seat Track Attach Screws in Rear Spar Cap01/01/1973
en Airframe - Inspection of Cabin Interior Structure10/01/1970
en Fuel System - Inspection of Inboard Leading Edge Fuel Cells03/01/1970
en Electrical (Cockpit and Nose Section) Conformity Inspection of Power Distribution Dual Bus System03/01/1970
1 en Propeller (Two-Blade) - Reconditioning of Sensenich Propellers06/01/1970
en Exhaust System - Use of Kano Kroil Penetrating Oil or Mouse Milk to Free Turbocharger Shafts Restricted by Rust Deposits05/01/1970
3 en Fuel System - Fuel Selector Valve - Inspection of Fuel Selector Valve01/01/1975
1 en Fuel System - Installation of Velcro Tap with Replacement Baffled Fuel Cells09/01/1971
1 en Heater Installation - Installation of Differential Pressure Switch11/01/1972
en Oil System - Inspection of Oil Return Line06/01/1970
en Electrical (Wing and Engine Section) - Installation of a Heated Wing Lift Transducer Assembly09/01/1970
1 en Control Column and Linkage - Inspection of Control Wheel Adapter01/01/1972
en Dry Air (Vacuum) Pump - Replacement of Drive Oil Seal06/01/1970
1 en Power Plant - Manifold Pressure Line Modification01/01/1974
6 en Structures - Part I: Inspection of Basic Structural Components - Part II: Replacement of Center Section Main Lower Spar Cap and Outboard Wing Main Spars - Part III: Inspection of Remaining Structure on Wing Center Section and Outboard Wings06/01/1977
7 en Structures - Part I: Inspection of Basic Structural Components - Part II: Replacement of Center Section Main Lower Spar Cap and Outboard Wing Main Spars - Part III: Inspection of Remaining Structure on Wing Center Section and Outboard Wings08/01/1978
en Power Plant - Inspection of Propeller Governor Drive Accessory Housing07/01/1970
en Firewall (Single Engine) - Sealing Hole in Firewall07/01/1970
en Fuel System (Engine Section) - Installation of Clamp on Flexible Fuel Hose07/01/1970
1 en Airframe - Inspection of Basic Structural Components06/01/1973
en Airframe - Inspection of Basic Structural Components11/01/1970
1 en Power Plant - Inspection of Engine Mount Bolt Nuts01/01/1973
en Nose Gear Retract Mechanism - Installation of Orifice Fitting in Nose Gear Hydraulic Retract Line08/01/1970
1 en Propeller Governor - Inspection of Control Linkage01/01/1971
en Electrical (Fuselage Section) - Insulation of Circuit Breaker Bus Bar and Installation of Ammeter Circuit Fuses10/01/1970
en Nose Gear Assembly - Inspection of Nose Wheel Axle for Corrosion10/01/1970
2 en Fuel System (Engine Section) - Inspection and Replacement of Fuel Hoses and Fittings on Engine Driven Fuel Pumps09/01/1973
1 en Electrical - Fuselage Section - Installation of 10-Ampere Starter Relay Circuit Breaker04/01/1972
1 en Power Plant - Installation of Restrictors in Fuel Pressure and Oil Pressure Lines07/01/1971
en Electrical (Fuselage Section) - Installation of a Switch for Strobe Light And/or Rotating Beacon Operation11/01/1970
en Landing Gear Hydraulic System - Modification of Plumbing at Main Gear Actuator Cylinder and Uplock Cylinder11/01/1970
en Flap Mechanism - Electric Flap System Modification11/01/1970
en Main Gear Assembly - Modification of Main Gear Up-Lock Cylinders12/01/1970
en Aileron and Aileron Tab Controls - Improvement of Cable Guard12/01/1970
en Utility Baggage Door - Inspection of Inside Handle Installation12/01/1970
en Elevator - Inspection of Hinge Points for Alignment and Spar for Cracks in Area of Outboard Hinge04/01/1971
en Pressure System - Service Exchange Program for Airborne 200CW Dry Air Pumps01/01/1971
en Heater Installation - Inspection of Heater Muffler Assembly02/01/1971
2 en Electrical (Wing and Engine Section) - Installation of Wing Lift Detector with Heated Vane11/01/1971
en Landing Gear Retract Mechanism - Modification of Nose Gear Retract Installation08/01/1971
en Power Plant - Cowling - Part I: Installation of Urethane Adhesive Rub Strips on Cowl Doors and Nose Cowl Bulkhead Flange; Part II: Increase of Flange Width at Forward End of Engine Compartment Side Panel Longerons12/01/1971
1 en Electrical - Fuselage Section - Installation of Smaller Capacity Circuit Breaker for Narco Avionics Mark 16 NAV/COM System01/01/1972
en Fuel System - Installation of Improved Fuel Quantity Sensors and Insulation of Sensors at Fuel Cell Liners05/01/1971
1 en Landing Gear - Main Gear Retract Mechanism - Installation of Up-Lock Roller Lubricating Bolt Assembly10/01/1972
1 en Landing Gear - Tire Clearances11/01/1977
1 en Flight Controls - Inspection of Elevator Hinge Points for Alignment and Elevator Spar for Cracks in Area of Outboard Hinge08/01/1978
2 en Electrical (Alternator) - Installation of Alternator Cooling Fan03/01/1973
1 en Horizontal Stabilizer - Installation of New Elevator Stop Bolts12/01/1971
en Instruments - Instrument Panel (Fixed) - Installation of Improved Oil Pressure and Temperature Gage09/01/1971
1 en Fuel System - Installation of Baffled Fuel Cells02/01/1976
en Landing Gear - Nose Gear Steering - Modification to Prevent or Eliminate Shimmy10/01/1971
2 en Landing Gear - Modification of Housing Installation10/01/1978
en Fuel System - Modification of Fuel Distribution System10/01/1971
en Power Plant - Removal of Oil Drain Hose11/01/1971
en Power Plant - Attach Fittings - Modification of Throttle Control Installation02/01/1972
1 en Power Plant - Removal of Oil Drain Hose04/01/1972
en Electrical - Alternator - Part I: Inspection of Alternator Mounting Bracket; Part II: Installation of New Alternator Housing through Bolts; Part III: Clearance Check Between Alternator and Alternator Mounting Bracket; Part IV: Reclamping of Alternator Wiring Bundle05/01/1972
2 en Fuel System - Inspection of Fuel Cell Vent Lines and Fuel Filler Caps06/01/1973
1 en Fuel System - Establish Minimum Fuel for Take Off, Increase Amount of Unusable Fuel and Inspect Baffled Fuel Cells05/01/1973
1 en Fuel System - Establish Minimum Fuel for Take Off and Increase Amount of Unusable Fuel05/01/1973
2 en Fuel System - Establish Minimum Fuel for Take Off and Increase Amount of Unusable Fuel05/01/1973
1 en Fuel System - Establish Minimum Fuel for Take Off and Increase Amount of Unusable Fuel05/01/1973
en Electrical - Fuselage Section - Inspection of 435-210-104 Circuit Breakers04/01/1972
en Electrical - Fuselage Section - Inspection of Circuit Breakers for Landing Gear Position Lights and Auxiliary Fuel Pump04/01/1972
en Heater Installation - Installation of New Differential Pressure Switches and Inspection of Heater Fuse06/01/1972
en Carpet and Floorboards - Installation of Straps and Attachments to Secure Tow Bar and Baggage10/01/1972
en Electrical (Fuselage Section) - Replacing Landing Gear Control Switch05/01/1972
en Placards (Interior) - Installation of Emergency Procedures - Engine Shut-Down Decal06/01/1972
en Wing - Wing Assembly - Installation of Strap Below Wing Aileron Push Rod Opening07/01/1972
1 en Flight Controls (Control Column and Linkage) - Installation of Roller Type Sprockets and Chains in Control Arm10/01/1973
en Fuel System - Fuel Selector Valve - Inspection of Fuel Selector Valve Detent Washer and Guard Markings11/01/1972
1 en Empennage - Vertical Stabilizer - Part I: Inspection of Vertical Stabilizer Main Spar for Fatigue Cracks and/or Nicks; Part II: Repair of Fatigue Cracks and/or Nicks in Vertical Stabilizer Main Spar and Angle-Doubler06/01/1975
en Landing Gear Safety System (Magic Hand) - Replacement of Pressure Switches11/01/1972
en Fuel System - Fuel Cap and Adapter - Inspection and Repair of Fuel Quantity Sight Gage12/01/1972
2 en Electrical Power - Alternator - Periodic Inspection of Rotor Shaft Bearings11/01/1976
1 en Fuel System - Part 1: Replacement of Rochester Fuel Transmitters; Part II: Inspection of Rochester Fuel Transmitters in Stock07/01/1973
1 en Power Plant - Relocation and Modification of Oil Cooler Installation05/01/1973
2 en Electrical Power - Alternator - Periodic Inspection of Rotor Shaft Bearings11/01/1976
2 en Cabin Furnishings - Seat (Pilot, Copilot and Passenger) - Installation of Additional Seat Track Stops04/01/1974
2 en Cabin Furnishings - Seat (Pilot, Copilot and Passenger) - Installation of Additional Seat Track Stops04/01/1974
en Power Plant Installation - Inspection of Propeller Governor Oil Line01/01/1973
en Heater Installation - Inspection Procedure for Heater
en Landing Gear (Nose Gear Steering) - Modification of Nose Gear Centering Cable04/01/1973
en Landing Gear (Main Gear Assembly) - Modification and Adjustment of Main Landing Gear Actuator02/01/1973
1 en Power Plant - Inspection and Replacement of Induction Air Ducts03/01/1974
2 en Power Plant - Inspection and Replacement of Induction Air Ducts04/01/1981
1 en Part I: Pitot and Static System - Inspection and Replacement of Clamps on 1/4" Pitot Hoses in Wings; Part II: Fuel System - Inspection of 1/4" Fuel Vent Hose Clamps in Wings08/01/1973
1 en Part I: Pitot and Static System - Inspection and Replacement of Clamps on 1/4" Pitot Hoses in Wings; Part II: Fuel System - Inspection of 1/4" Fuel Vent Hose Clamps in Wings08/01/1973
en Wing Installation - Part I and Part II: Inspection of Upper Forward Wing Bolts for Correct Washers; Part III: Inspection of Lower Forward Wing Fittings for Impressions Caused by Incorrect Radius on Torque Washers05/01/1973
en Powerplant - Modification of Carburetor Airbox Valve05/01/1973
en Landing Gear - Landing Gear Safety System (Magic Hand) - Addition of Magic Hand Flight Manual Supplement to Airplane Flight Manual05/01/1973
en Landing Gear - Inspection of Landing Gear Shock Strut Piston05/01/1973
en Pressure System (Instrument) - Installation of an Improved Pressure System Intake Filter08/01/1973
1 en Engine Controls - Modification of Carburetor Throttle Arm Attachment11/01/1973
1 en Seats (Passenger) - Installation of Improved Aft Facing Seat Back Supports01/01/1973
2 en Fuselage - Windows - Installation of an Improved Pilot's Side Window04/01/1974
en Avionics - Antenna Installation - Reinforcement of Emergency Locator Antenna Mount09/01/1973
en Instruments - Pitot and Static System - Modification of Static Air System to Reduce Moisture Accumulation04/01/1974
1 en Flight Controls - Engine Controls - Inspection and/or Replacement of Fuel Mixture Control and Carburetor Heat Control11/01/1974
2 en Flight Controls - Elevator Trim Tab - Modification of Elevator Trim Tab Installation06/01/1975
1 en Landing Gear - Inspection of Landing Gear Shock Strut Piston01/01/1974
en Electrical - Nose Section - Removal of S550 Klipvolt Suppressor from Battery Master Relay and Installation of 1N4005 Diode11/01/1973
1 en Pitot and Static System - Inspection of Static Air Line Splices in Fuselage for Possible Restriction04/01/1974
2 en General - Gross Weight Modification04/01/1974
en Flight Controls - Engine Controls - Inspection of Vernier Controls for Proper Rigging11/01/1973
en Flight Controls - Elevator and Tab Controls - Modification to Secure Elevator Stop Bolts03/01/1974
en Fuselage - Installation of Kit to Allow Intentional Spins02/01/1974
en Landing Gear - Main Gear and Doors - Replacement of Door Attaching Bolt with a Bolt Containing a Lubrication Fitting12/01/1973
en Fuel System - Fuel Selector Valve - Installation of a New Improved Fuel Selector Valve Assembly08/01/1974
en Fuel System - Replacarding to Indicate Minimum Fuel for Take Off and Increase Amount of Unusable Fuel06/01/1974
en Power Plant - Propeller, Two Bladed - Installation of McCauley Propellers as Alternate Replacements on Earlier Debonair/Bonanza Aircraft01/01/1974
en Wing - Wing Assembly - Part I: Inspection and Replacement of Jo-Bolts on Main Landing Gear Forward Support Castings; Part II: Inspection and Replacement of Main Landing Gear Aft Support Castings01/01/1974
en Engine Controls - Power Control - Modification of Engine Quadrant Controls Friction Mechanism01/01/1974
en Fuel System - Inspection of Fuel Vent Lines for Possible Obstruction01/01/1974
en Flight Controls - Inspection for Proper Screws on Rudder and Elevator Hinges and on Rudder, Elevator and Aileron Bell Cranks01/01/1974
2 en Flight Controls - Inspection for Proper Screws on Rudder and Elevator Hinges and on Rudder, Elevator and Aileron Bell Cranks09/01/1978
1 en Fuel Cells - Inspection of Condition of Fuel Cells and Possible Seepage of Fuel05/01/1978
1 en Flight Controls - Engine Controls - Installation of Spacer Between Bracket and Mixture Control Cable Clamp07/01/1974
1 en Power Plant - Inspection of Plumbing Fittings at Firewall01/01/1976
en Fuel System - Part I: Replacement of Outboard Fuel Transmitters in Inboard Wing Leading Edge, and Securing of Fuel Cells to Wing Liners at Fuel Transmitters; Part II: Installation of an Insulator Strip on Wing Leading Edge Covers04/01/1974
en Vacuum or Pressure System - Installation of a New Improved Instrument Air Pump04/01/1974
en Landing Gear - Modification of Hydraulic Shuttle Valve04/01/1974
en Fuselage - Assist Step - Replacement of Cabin Assist Steps05/01/1974
en Instrument Panel - Modification of Airspeed Indicator Markings05/01/1974
en Electrical - Strobe Lights - Modification of Grimes P/N 30-0467-I and P/N 30-0467-3 Strobe Light Installations08/01/1974
1 en Electrical - Strobe Lights - Modification of Grimes P/N 30-0467-I and P/N 30-0467-3 Strobe Light Installations10/01/1974
en Fuselage - Cargo Door or Utility Baggage Door - Installation of an Improved Latch on Forward Cargo/Utility Door11/01/1974
en Flight Controls - Control Column and Linkage - Modification of Control Gust Lock06/01/1974
en Fuel Systems - Inspection for Possible Fuel Seepage from Fuel Cells06/01/1974
en Miscellaneous - Time Limits - Observing Initial Time between Overhaul09/01/1974
1 en Power Plant - Replacement of Carburetor and Modification of Carburetor Air Box04/01/1979
en Fuel System - Replacement of Fuel Drain Lines for Clearance of Heat Sinks08/01/1974
en Fuel System - Fuel Selector Valve - Replacement of Fuel Selector Valve Handle11/01/1974
en Flight Controls - Elevator and Tab Controls - Replacement of Elevator Bell Crank Pivot Bolt and Nut10/01/1974
en Electrical - Instruments - Installation of a Higher Amperage Navigation Light Circuit Breaker09/01/1974
1 en Placards - Installation of a Cleaning Instructions Decal for Plastic Interior Trim02/01/1976
2 en Instrument - Subpanel - Inspection of Fuel Quantity and Oil Temperature Indication Systems10/01/1976
en Landing Gear - Landing Gear Retract Mechanism - Inspect for Proper Installation of Bolt on Main Landing Gear Retract Mechanism and Install Instruction Decal10/01/1974
en Landing Gear - Main Gear Assembly - Increased Tire Clearance on Main Landing Gear Struts10/01/1974
1 en Instruments- Pitot and Static System - Installation of Optional Emergency Static Air Valve03/01/1977
en Fuselage - Baggage Door (Aft) - Addition of Decal11/01/1974
en Power Plant - Induction System - Installation of a Clamp on Induction Air Hose01/01/1975
1 en Cabin Furnishings - Upholstery - Inspection of Soundproof Blanket for Proper Installation12/01/1978
1 en Electrical - Alternator - Modification of Alternator Attachment and Security of Wiring08/01/1975
1 en Flight Controls - Pedestal or Console Structure - Replacement of Quadrant Control Cover05/01/1975
en Vacuum or Pressure System (Instrument) - Replacement of Vacuum Pump Hose01/01/1975
en Power Plant - Exhaust System - Inspection and Modification of Turbocharger Wastegate Elbow02/01/1975
en Flight Controls - Engine Controls - Inspection of Mixture Control and Carburetor Heat Control Cables06/01/1975
en Power Plant - Calibration and Functional Test of Tachometers and Manifold Pressure Indicators and Installation of Limitation Placard04/01/1975
en Landing Gear - Installation of Improved Nose Landing Gear Limit Switch07/01/1975
en Stabilizers - Inspection of Stabilizer Attaching Fitting05/01/1975
2 en Stabilizers - Inspection of Stabilizer Attaching Fitting05/01/1976
en Doors - Replacement of Door Handles and Cabin Door Latch Bolts05/01/1975
en Landing Gear - Landing Gear Retract Mechanism - Modification of Uplock Bracket06/01/1975
1 en Fuselage Mainframe - Addition of Drain Holes in Lower Fuselage Skin01/01/1977
en Power Plant - Manifold Pressure Fitting Modification06/01/1975
en Landing Gear - Installation of Improved Restrictor Check Valve in Main Gear Actuators06/01/1975
en Auto Flight - Modification of Collins API05 Autopilot Aileron Servo System07/01/1975
en Propellers - Modification of N1 Speed, Low Pitch and Ice Vane Sense Module Assembly06/01/1975
en Flight Controls - Inspection of Control Column and Mixture Control Cable for Clearance08/01/1975
en Flight Controls - Pedestal Structure - Inspection of Flap and Stabilator Tab Control Pedestal07/01/1975
en Propellers - Installation of Fiber Spacer Washer on Hartzell Spinner Assemblies07/01/1975
en Electrical Power - Inspection of Terminal Block Assemblies08/01/1975
2 en Fuselage - Inspection of Aft Bulkhead and Horizontal Stabilizers Aft Spars06/01/1978
en Flight Controls - Control Column - Inspection of Control Column Installation08/01/1975
en Pneumatic System - Inspection and Modification of Airborne 440 Series Dry Air Pump08/01/1975
en General - Inspection and/or Replacement of Control Rod End Bearings08/01/1975
en Propellers - Replacement of Propeller Governor09/01/1975
en Electrical Power - Rerouting of Generator Leads in Engine Compartment10/01/1975
en Fire Protection - Inspection of Fire Shield Installation01/01/1976
en Fuel System - Inspection of Nacelle Fuel Cell Fuel Vent Float Valve10/01/1975
en Wings - Inspection of Wing to Center Section Attachment at Lower Forward Spar Cap11/01/1975
en Flight Controls - Inspection of Rudder Push Rod Assembly01/01/1976
en Power Plant - Relocation of Tachometer Drive Cable Housing12/01/1975
en Equipment/Furnishings - Replacement of Chair Locking Pins01/01/1976
en Flight Controls - Installation of Improved Elevator Trim Tab Actuator Tube Assemblies01/01/1976
1 en Doors - Installation of Improved Latch Assembly on Large Baggage Door01/01/1980
2 en Flight Controls - Inspection of Elevator Main Spar and Outboard Leading Edge Rib Flanges for Possible Cracks10/01/1976
1 en Lights - Replacement of Hoskins P/N 30-0187-21 and Grimes P/N 30-0669-1 Wing Strobe Lights02/01/1977
1 en Fuel System - Replacement of Fuel Cap and Adapter11/01/1979
en Electrical Power - Modification to Battery Box Installation10/01/1976
1 en Propeller - Removal of Secondary Low Pitch Stop System02/01/1977
2 en Propeller - Removal of Secondary Low Pitch Stop System03/01/1978
en Fire Protection - Inspection of Fire Shield Installation03/01/1976
en Landing Gear - Inspection of Tire to Brake Backplate Clearance03/01/1976
2 en Placards and Markings - Add Caution to Cabin Door Instruction Plate05/01/1977
en Ice and Rain Protection - Inspection of Surface Deicer Lines03/01/1976
en Communication - Compliance with Federal Air Regulations 91.17705/01/1976
2 en Wings - Inspection of Main Spar11/01/1977
en Doors - Modification of Cargo Door Latch Support Bracket04/01/1976
1 en Windows - Inspection and Reinforcement of Left Cabin Window Forward of Rear Cabin Door08/01/1978
en Flight Controls - Inspection and Modification of Flap Cable Block04/01/1976
en Flight Controls - Inspection of Clutch Wiring on Electric Elevator Trim Tab Actuator04/01/1976
en Engine Fuel and Control - Inspection of Manual Mixture Control Shaft08/01/1976
en Nacelles - Modification of Engine Firewall04/01/1976
en Fuel System - Replacement of Fuel Selector Valve09/01/1976
en Equipment/Furnishings - Modification to Pilot and Copilot Seats07/01/1976
1 en Equipment/Furnishings - Modification of Seat Belts Installed with Inverted "Y" Type Shoulder Harness04/01/1977
en Flight Controls - Inspection and/or Replacement of Rod Ends08/01/1976
en Fuel - Replacement of Fuel Boost Pump09/01/1976
en Fuel System - Modification of Fuel Pump Air Cooling System when a New Engine or a New Fuel Pump is Installed11/01/1976
2 en Oxygen - Installation of a Moisture Sealed Oxygen Control Cable10/01/1979
3 en Oxygen - Installation of a Moisture Sealed Oxygen Control Cable06/01/1980
en Fuselage - Installation of Kit to Allow Intentional Spins12/01/1976
1 en Electrical Power - Replacement of Voltage Regulator and Overvoltage Relay05/01/1979
en Nacelles/Pylons - Inspection of Attach Bolts in Engine Mount Fittings12/01/1976
en Placards - Installation of a Plate on Standby Generator Switch01/01/1977
1 en Propellers - Procedure for Dome Installation of Hartzell Feathering Compact Propellers05/01/1981
en Landing Gear - Replacement of Dynamic Brake Relay01/01/1977
en Air Conditioning - Inspection of Pressurization Control Vacuum Source Line for Proper Clearance01/01/1977
en Windows - Installation of Curtains or Blinds and Tinted Inner Windows as Replacements for Polarized Windows02/01/1977
en Flight Controls - Replacement of Rudder Boost Servo Cables01/01/1977
en Power Plant - Inspection of Induction Air Filter Installation01/01/1977
en Power Plant - Installation of Skin Reinforcement at Lower Cowling Air Bypass Outlet02/01/1977
en Windshield - Inspection of Anti-Static Tab Bonding04/01/1977
en Doors - Inspection of Cabin Entrance Step Strut02/01/1977
en Flight Controls - Modification of Control Gust Lock Installation02/01/1977
en Heating - Addition of Second Check Valve to Fuel Plumbing04/01/1977
en Flight Controls - Inspection of Control Columns and Elevator Control Arm Assembly02/01/1977
en Landing Gear - Inspection of Main Landing Gear Torque Tubes03/01/1977
en Vacuum System - Relocation of Air Filter03/01/1977
en Flight Controls - Installation of Stall Warning Transducer with Increased Heat Rating08/01/1977
en Navigation - Revised Maximum Allowable Vmo and Mmo06/01/1977
1 en Fuel System - Inspection of Goodyear Fuel Cells12/01/1979
en Electrical Power - Inspect Bus Bars for Clearance from LH Rudder Control Cable03/01/1977
en Nacelles/Pylons - Inspection of Main Gear Wheel Well Fender Installation for Possible Loose Rivets and Modification of Wheel Well Fender Brackets03/01/1977
en Fuselage - Installation of Additional Rivets in Aft Wing Spar and Lower Cabin Structure03/01/1977
en Air Conditioning - Replacement of Radiant Heat Thermostats in Cabin Headliner04/01/1977
en Communications - Part I, Improved Static Discharge Bonding; Part II, Installation of Additional Static Discharge Wicks04/01/1977
en Electrical Power - Inspection for Wire Clearance04/01/1977
en Doors - Modification of Air Stair Door Handrail04/01/1977
2 en Power Plant - Inspection of Engine Mount Truss Tubes05/01/1978
en Fuel System - Replacement of Fuel Boost Pump04/01/1977
en Air Conditioning - Cabin Temperature Gage Adjustment09/01/1977
en Flight Controls - Rerigging of Aileron Neutral Position04/01/1977
en Exhaust System - Installation of Improved Exhaust Pipes05/01/1977
en Electrical Power - Replacement of Alternator Field Circuit Breaker05/01/1977
en Auto Flight - Installation of a Diode in Marker Beacon Circuitry05/01/1977
en Equipment/Furnishings - Installation of Improved Seat Tie Down for 5th and 6th Seats05/01/1977
en Ice and Rain Protection - Inspection of Inertial Vane and Bypass Door Rigging05/01/1977
en Air Conditioning - Installation of an Improved Crossover Duct05/01/1977
en Fuel Storage - Modification to Install Wet Wing Tips05/01/1977
1 en Doors - Inspection of Cabin Door Latch Hooks and Lock Pins for Proper Adjustment10/01/1977
1 en Wings - Replacement of Rivets on the Inboard Aileron Hinge Arms01/01/1978
en Servicing - Sealing Minor Leaks in Rim-Inflated Tubeless Tires07/01/1977
en Conditioned Air - Installation of an Improved Air Source for Cabin Door Seal Pressurization08/01/1977
en Exhaust - Extension of Engine Turbocharger Exhaust Stacks06/01/1977
en Air - Improved Engine Bleed Air Regulator Installation06/01/1977
en Instruments - Installation of New Engine Instrument Cluster Kit06/01/1977
en Fuel Indicating - Installation of Improved Fuel Probe Gasket06/01/1977
en Fuel - Installation of Improved Engine Fuel Strainers06/01/1977
en Air Conditioning - Installation of an Improved Start Control Resistor Mount09/01/1977
en Fuel - Inspection of Fuel Pumps06/01/1977
3 en Fuel - Replacement of Fuel Transmitters and Gages10/01/1979
en Power Plant - Improved Grounding of Unfeathering Pump07/01/1977
1 en Fuselage - Installation of Wire Bundle Bracket Assembly03/01/1978
en Propellers - Provisions for Dynamic Propeller Balancing09/01/1978
en Placards - Installation of a Fuel Return Decal11/01/1977
1 en Wings - Inspect Scuff Pads in Wet Wing Tips & Install an Improved Clap Assembly if Necessary02/01/1979
1 en Landing Gear - Replacement of Non-Lubricated Bearing Eye Assembly in Nose Wheel Steering03/01/1980
en Fuselage - Inspection and Installation of a Reinforcement to F.S. 68.00 Bulkhead08/01/1977
en Vacuum System - Service Life Limitation of Airborne Dry Air Pumps08/01/1977
en Air Conditioning - Relocation of Bleed Air Flow Test Points08/01/1977
en Navigation - Relocation of Static Air Drains08/01/1977
en Equipment/Furnishings - Installation of Soundproofing on Aft Pressure Bulkhead11/01/1977
1 en Equipment/Furnishings - Notice of Availability of Shoulder Restraint Belts for Passengers09/01/1970
en Landing Gear - Installation of Additional Landing Gear Safety Switch09/01/1977
2 en Electrical Power - Dual Bus Feeder Circuit Inspection04/01/1978
1 en Flight Controls - Replacement of Flap Control Weld Assembly08/01/1979
en Air Conditioning - Installation of Improved Refrigerant Pressure Release Valve02/01/1978
1 en Equipment/Furnishings - Aft Compartment Shoulder Harness09/01/1980
1 en Landing Gear - Installation of a Relay in Landing Gear Retract Circuit09/01/1978
en Wings - Reduction of Precipitation Static Noise12/01/1977
en Electrical Power - Installation of Larger Gage Wires from Alternator Field Circuit Breaker to Voltage Regulator10/01/1977
en Fuselage - Clip Installation Inspection10/01/1977
en Landing Gear - Emergency Landing Gear Extension Handle04/01/1978
en Electrical - Modification of Heated Stall Warning Circuit10/01/1977
en Air Conditioning - Insulation of 33â° Refrigerant Freeze Protection Switch10/01/1977
en Air Conditioning - Replacement of Heat Exchanger Air Inlet Duct Assemblies10/01/1977
1 en Engine Controls - Modification of Engine Fuel Condition & Underspeed Governor Control11/01/1978
en Nacelles/Pylons - Modification of Landing Gear Drag Leg Support11/01/1977
en Landing Gear - Inspection of Brake System Tube Assembly11/01/1977
en Power Plant - Inspection of Engine Bleed Air Outlet Duct Seals10/01/1977
en Avionics - Replacement of Avionics Power Relays11/01/1977
en Doors - Removal of Cabin Door Safety Chain11/01/1977
en Fuel System - Inspection of Fuel Vent Hose in Outboard Wing Leading Edge Fuel Cells11/01/1977
en Power Plant - Inspection & Replacement of Turbocharger Air-Oil Separators11/01/1977
1 en Flight Controls - Increased Aileron Cable Tension02/01/1978
en Flight Controls - Inspection of Flap Safety Switch Linkage12/01/1977
en Auto Flight - Inspection for Possible Interference between Aileron Servo Cable Clamp and Flap Position Indicator Transmitter11/01/1977
en Fuselage - Improved Water Drainage from Aft Fuselage11/01/1977
en Landing Gear - Part I, Increased Power Setting for Landing Gear Warning Horn System; Part II, Modification of Landing Gear Warning Horn System Wiring02/01/1979
en Air Conditioning - Nacelle Airscoop Actuator Replacement12/01/1977
en Air Conditioning - Inspection of Firewall Elbow Fitting01/01/1978
en Landing Gear - Inspection for Vent Hole in Brake Fluid Reservoir01/01/1978
en Air Conditioning - Installation of High Pressure Plumbing & a New High Pressure Switch01/01/1978
en Equipment/Furnishings - Installation of Closure Angles on Upholstery Scuff Panels01/01/1978
en Landing Gear - Inspection of Main Landing Gear Wheel Bearings02/01/1978
en Doors - Inspection of Assist Steps02/01/1978
en Ice & Rain Protection - Part I, Heated Windshield Voltage Check; Part II, Relocation of Windshield Inverter Power Wiring04/01/1978
1 en Fuel System - Part I, Replacement of Check Valve; Part II, Inspection of Fuel Jet Transfer Pump Check Valve12/01/1978
1 en Propellers - Removal of Two Speed Propeller Governor System05/01/1979
en Engine - Replacement of Bearing Oil Pressure Lines03/01/1978
en Flight Controls - Replacement of Flap Relays & Modification of Flap Relay Circuit03/01/1978
en Engine Controls - Replacement of Fuel Control Unit Diaphragm03/01/1978
1 en Air Conditioning - Installation of Eyeball Air Outlets in Glareshield04/01/1980
en Air Conditioning - Modification of Bleed Air Bypass Valve Assembly03/01/1978
en Flight Controls - Overheat Protection for Heavy Duty Heated Stall Warning Vane03/01/1978
en Navigation - Installation of a Drain on Static Air Line04/01/1978
en Landing Gear - Brake Deicer Installation04/01/1978
en Auto Flight - Sperry SPZ-200A Flight Control System Heading Mode Roll Rate Modification04/01/1978
en Power Plant - Installation of a Fuel Drain Firesleeve04/01/1978
en Structures - Part I, Replacement of Center Section Main Lower Spar Cap & Outboard Wing Main Spar & Installation of Rear Spar Reinforcement; Part II, Inspection of Remaining Structure on Wing Center Section & Outboard Wings08/01/1978
en Fuel System - Modification of Fuel Drains05/01/1978
en Flight Controls - Inspection and Modification of H-14 Autopilot Elevator Servo Installation05/01/1978
1 en Flight Controls - Inspection of Ruddervator Control Push Rods11/01/1981
2 en Fuselage - Inspection of FS 257.6 and FS 271.92 Bulkheads at Forward and Aft Horizontal Stabilizer Stub Spars05/01/1980
en Landing Gear - Inspection of Landing Gear Position Light Wiring05/01/1978
en Air Conditioning - Change of Turbine Oil in Super Charger Drive System05/01/1978
en Oil - Remote Mounting of Oil Pressure Transducer & Installation of an Improved Oil Pressure Snubber08/01/1978
en Flight Controls - Inspection of Stabilator Trim Tab Actuator Rod05/01/1978
en Wing - Inspect Upper Wing Surface for Cracks & Repair if Necessary05/01/1978
en Engine Turbine/Turboprop - Installation of an Improved Oil Pressure Relief Valve Assembly05/01/1978
en Fuel System - Inspection of Fuel Selector Valve Control Cable Housings06/01/1978
en Power Plant - Inspection and/or Replacement of Hose Assemblies06/01/1978
en Fuel System - Part I, Preflight Inspection for Flammable Fuel Leaks in Engine Compartment and Nacelle; Part II, Replacement of Flammable Fluid and Vapor Carrying Hose Assemblies in Engine Compartment; Part Ill, Installation of Engine Fire Detector System06/01/1978
en Equipment/Furnishings Modification or Replacement of Cabin Ash Tray & Cup Holder Assemblies06/01/1978
en Ice & Rain Protection Anti-Icing/Deicing Modification07/01/1978
en Air Conditioning - Installation of Guard on Cabin Door Seal Deflate Button07/01/1978
en Communications - Installation of Bond Jumpers, Drain Tubes & Conductive Strips08/01/1979
en Nacelle - Installation of a Doubler to Cover Unused Holes in Left Nacelle Fuel Cell Liner08/01/1978
en Doors - Part I, Removal of Screw from Arm Rest on Cabin Entrance Door; Part II, Addition of Door Lock Stop; Part III, Addition of Drain Hole in Door Pressure Lock08/01/1978
en Fuel - Fuel Drain Line Rerouting08/01/1978
en Air Conditioning - Inspection of Heater Combustion Air Intake Scoop Position09/01/1978
en Engine Controls - Modification of Engine Control Lever Friction Brake Assemblies09/01/1978
en Communications - Installation of Static Discharge Wicks12/01/1978
en Equipment/Furnishings - Improved Sun Visor Installation09/01/1978
en Engine - Part I, Turbine Wheel Life Limits; Part II, Propeller Pitch Control Assembly09/01/1978
en Oil System - Installation of Support for Oil Supply Tube10/01/1978
1 en Power Plant - Installation of Improved Fuel Drain Lines07/01/1979
en Electrical Power - Improve Overvoltage Relay Reaction Time10/01/1978
en Wings - Installation of a Wedge Strip to Improve Aileron Centering10/01/1978
en Flight Controls - Inspection of Control Column Bearing Assemblies02/01/1979
en Air Conditioning - Improved Corrosion Prevention for Evaporator Tubes11/01/1978
en Flight Controls - Inspection of Elevator Control Push Rods01/01/1980
2 en Fuel System - Modification of Fuel Vent Plumbing07/01/1980
en Pneumatic - Replacement of Plastic Tubing in Door Seal Plumbing System12/01/1979
1 en Pneumatic - Improved Flow Control Valve Seal05/01/1979
en Flight Controls - Installation of a Spacer in Elevator Bell Crank11/01/1978
en Ignition - Installation of an Improved Ignition Power Relay11/01/1978
en Electrical Power - Inspection of Wire Bundle for Possible Chafing12/01/1978
en Electrical Panels, Parts & Instruments - Inspect for Lockwashers on Cutler-Hammer Rocker Switches and Install as Necessary12/01/1978
1 en Stabilizers - Close Bird Entrances in Rudder06/01/1979
en Engine Controls - Replacement of Engine Control Lever Friction Brake Assemblies01/01/1979
en Landing Gear - Inspection of Nose Landing Gear Limit Switch Installation02/01/1979
en Landing Gear - Inspection of Uplock Stop02/01/1979
en Navigation/Pitot and Static - Improved Sealing of Emergency Static Air Source Valve02/01/1979
en Lights - Installation of a Mounting Plate for Wing Tip Mounted Nav and Strobe Light Assemblies03/01/1979
1 en Electrical Power - Modification of Electrical System and Improved Alternator Paralleling09/01/1979
en Oil - Improved Grounding of Oil Pressure Transducers03/01/1979
1 en Electrical Power - Improve Voltage Regulator Sensing Response08/01/1980
en Stabilizers - Inspection of Elevator Trailing Edge Bond Thickness04/01/1979
1 en Landing Gear - Installation of Improved Dust Boots on Nose Gear Steering and Retract Rods03/01/1980
en Navigation/Pitot & Static - Installation of a Dual Static System04/01/1979
en Power Plant - Replacement of Cowl Flap Hinge Assemblies04/01/1979
en Engine Fuel and Control - Modification of Carburetor04/01/1979
en Flight Controls - Inspection for Installation of a Ground Wire on Flap Position Transmitter04/01/1979
1 en Landing Gear - Modification of Landing Gear Warning Horn System09/01/1979
en Equipment/Furnishings - Removal of Lithium Sulfur Dioxide Batteries04/01/1979
en Landing Gear - Inspection and/or Replacement of Landing Gear Torque Tube04/01/1979
en Equipment/Furnishings - Pilot's Operating Handbook and FAA Approved Airplane Flight Manual Revision Requirements04/01/1979
en Doors - Replace of Door Lock Assemblies04/01/1979
en Engine Controls - Installation of Ice Shields for Engine Fuel Mixture Controls04/01/1979
en Fuel - Part I, Installation of a Check Valve on Fuel Tank Outlet; Part II, Installation of an Improved Fuel Selector Valve04/01/1979
en Engine Fuel & Control - Installation of Improved Carburetor Airboxes04/01/1979
en Landing Gear - Replacement of Brake Shuttle Valves10/01/1979
en Flight Controls - Replacement of Elevator and Rudder Tab Push Rods05/01/1979
en Engine Fuel and Control - Inspection of Bendix Fuel Injector Assemblies on Avco Lycoming Engines05/01/1979
en Fuel - Inspection Fuel Line Fitting05/01/1979
en Air Conditioning - Relocation of Door Seal Emergency Deflate Valve07/01/1979
en Wings - Inspection of Fuel Tank Outboard Rib Attach Bolts05/01/1979
1 en Electrical Power - Installation of an Overvoltage Relay for 60 AMP Alternator System02/01/1980
en Wings - Inspection and/or Replacement of Aileron Trim Tab Outboard Hinge Assembly05/01/1979
en Fuselage - Inspect of Seals on Windshield, Cabin Windows, Firewall and FS 68.00 Frame05/01/1979
en Engine Indicating - Inspect Engine Instrument Cluster Assembly06/01/1979
en Engine Controls - Installation of an Improved Engine Control Quadrant Cover06/01/1979
en Equipment/Furnishings - Modification of Forward RH Cabin Service Panel Retainer07/01/1979
1 en Fuselage - Installation of Water Seal Cover in Avionics Compartment Floor10/01/1979
1 en Lights - Modification to Provide Dimming of Fuel No Transfer Lights03/01/1980
en Wings - Inspection and Repair Wing of Spar Center Splice Plates06/01/1979
1 en Oil - Installation of an Improved Oil Pressure Transducer & Indicator01/01/1980
en Landing Gear - Installation of an Improved Flathead Pin on Main Landing Gear Fork Pin07/01/1979
en Navigation - Replacement of Antenna Cables on Factory Installed Collins ADF-650 Installations04/01/1980
1 en Ice and Rain Protection - New Propeller Deicer Brush Block02/01/1982
en Doors - Replacement of Door Stop Assemblies08/01/1979
1 en Flight Controls - Inspect Rudder Torque Tube for Corrosion & Provide an Improved Drain04/01/1982
en Air Conditioning - Installation of Additional Refrigerant Service Ports10/01/1979
en Doors - Addition of Drain Holes in Cabin Airstair Door Pressure Lock08/01/1979
en Engine Indicating - Replacement of Manifold Pressure Fitting04/01/1980
en Ice & Rain Protection - Inspection of Inertial Vane Override Assembly09/01/1979
en Navigation/Pitot & Static - Inspection of Instrument Static Air Plumbing for Sperry SPZ-200A Autopilot10/01/1979
en Landing Gear - Installation of a Clamp to Secure Brake Line to Landing Gear Fork10/01/1979
en Ignition - Installation of a Cap on Unused Magneto Tachometer Contact10/01/1979
en Engine Controls - Replacement of Engine Control Cable Half-Ball Grommets10/01/1979
en Flight Controls - Inspection and/or Replacement of Stop Bolt Nuts for Aileron and Rudder Bell Cranks10/01/1979
en Wings - Inspection of Wing Attach Bolts and Attach Bolt Nut Plate Treads10/01/1979
en Navigation/Pitot Static - Provide an Improved Ground for Nav Antenna Cable10/01/1979
en Oxygen - Inspection of Oxygen Line for Possible Chafing Against Left Rear Cigarette Lighter10/01/1979
en Lights - Grounding Shield on Strobe Light Wiring11/01/1979
en Placards and Markings - Installation of Improved Fuel Placarding12/01/1979
en Placards and Markings - Installation of Placard for Use with Utility Doors Removed01/01/1980
1 en Mandatory Fuel System - Addition of a Decal and a Fuel Selector Stop to Fuel Selector Valve Guard07/01/1980
en Electrical Power - Addition of a Spare 150 Amp Current Limiter for Landing Gear Motor11/01/1979
en Landing Gear - Installation of an Improved Brake Hose01/01/1980
en Air Conditioning - Installation of Diode in Condenser Door Actuator Wiring12/01/1979
en Wings - Installation of Improved Nuts and Torque Indicating Washer Assemblies on Lower Forward Wing Attach Bolts12/01/1979
1 en Engine Fuel and Control - Replacement of Engine Driven Fuel Pump05/01/1982
en Engine Fuel & Control - Relocation of RH Fuel Flow Transmitter01/01/1980
en Pneumatic - Installation of Improved Instrument Air Lines12/01/1979
en Fuel - Insulation of Fuel Lines in Vicinity of Auxiliary Fuel Pump01/01/1980
en Landing Gear - Paint Application for Improved Corrosion Protection01/01/1980
en Fuel System - Inspection of Nacelle Fuel Cell Cover Vents & Nacelle Fuel Cell Installation01/01/1980
1 en Air Conditioning - Inspection of Airesearch Outflow/Safety Valves11/01/1980
en Autoflight - Modification of King KFC 300 Autopilot Wiring01/01/1980
1 en Stabilizers - Improved Attachment of Elevator Control Horns to Elevator Torque Tubes01/01/1981
en Oxygen - Replacement of Passenger & Copilot Oxygen Mask Assemblies01/01/1980
en Fuel - Improved Moisture Protection for Fuel Quantity System02/01/1980
en Landing Gear - Main Landing Gear Door Retract Mechanism Improvement12/01/1981
en Flight Controls - Inspection of Rudder Torque Tube02/01/1980
en Stabilizers - Installation of Drain Holes in Rudder and Rudder Trim Tab02/01/1980
en Electrical Power - Replacement of Load Meter 15 Amp Fuses and Spares with 5 Amp Fuses and Spares02/01/1980
en Lights - Modification of Tail Strobe Light Synchronizing Wiring02/01/1980
en Flight Controls - Replacement of Aileron Torque Tube Bearings02/01/1980
en Doors - Improved Sealing of Avionics Compartment02/01/1980
en Flight Controls - Installation of Improved Flap Switches02/01/1980
en Engine Controls - Installation of Improved Feathering Stop Spring04/01/1980
en Engine Controls - Replacement of Mixture Control Cable Assembly06/01/1980
en Control Column - Installation of a Foot Guard05/01/1980
en Air Conditioning - Installation of a Drain on Door Seal Air Tank03/01/1980
1 en Doors - Modification of Aft and Nose Hinged Baggage Door Latching Mechanism10/01/1981
en Doors - Replace Aft Cabin Door Lock Pin Seal Assembly03/01/1980
en Electrical Power - Installation of Bus Bar on Alternator, Battery and Engine Ground Connections04/01/1980
en Ice and Rain Protection - Replacement of Horizontal Stabilizer Deicer Boots04/01/1980
en Oxygen - Notification of Availability of Modification Kits for Crew Compartment Oxygen Mask Assemblies12/01/1980
en Placards and Markings - Replacement of Nose Gear Strut Servicing Placard04/01/1980
en Power Plant - Modification of Alternate Air Door04/01/1980
en Air Conditioning - Modification To Install Airesearch Pressurization System04/01/1980
en Placards and Markings - Inspection to Verify Installation and Condition of All Interior and Exterior Placards and Markings04/01/1980
en Flight Controls - Replacement of Elevator Control Arm Bushings04/01/1980
en Flight Controls - Installation of Improved Control Lock Assembly04/01/1980
en Navigation/Pitot and Static - Modification of Sperry RD-444 Horizontal Situation Indicator Wiring Harness04/01/1980
en Flight Controls - Inspection of Rudder Torque Shaft05/01/1980
1 en Equipment/Furnishings - Inspection and/or Replacement of Collins/Communications Components Corporation Emergency Locator Transmitters and/or Battery Packs09/01/1980
en Wings - Inspection and/or Replacement of Wing Attach Bolts, Nuts & Inspection of Wing Attach Fittings12/01/1981
en Air Conditioning - Installation of a Condenser Blower Relay Diode05/01/1980
en Exhaust - Inspection and/or Replacement of Muffler Assembly and Installation of a Carbon Monoxide Detector and Decal06/01/1980
en Electrical Power - Modification of Battery Box Installation08/01/1980
en Indicating/Recording Systems - Installation of an Improved Electric Hour Meter Pressure Switch06/01/1980
en Landing Gear - Installation of an Improved Main Landing Gear Side Brace Spring Pivot Assembly and Bushing06/01/1980
en Electrical Power - Installation of an Alternator Output Current Limiter09/01/1980
1 en Powerplant - Inspection and/or Replacement of Engine Mount Assemblies03/01/1982
en General - Gross Weight and Performance Modification09/01/1980
en Landing Gear - Installation of an Improved Nose Landing Gear Retract Rod Plunger10/01/1980
en Stabilizers - Inspection and Possible Rework of Horizontal Stabilizer Rear Spar10/01/1981
en Communications - Inspection and/or Replacement of Aileron Bond Jumpers01/01/1981
en Placards and Markings - Part I, Replacement of Airspeed Limitation Edgelite Panel Assembly; Part II, Replacement of Fuel Control Edgelite Panel Assembly12/01/1980
en Power Plant - Inspection of Engine Mount Assembly to Firewall Attach Bolts10/01/1980
1 en Fuel System - Inspection of Vapor Return Check Valve for Proper Installation05/01/1981
en Electrical Power - Replacement of Avionics Bus Feed Wire10/01/1980
en Landing Gear - Installation of a Fitting on Landing Gear Safety Switch11/01/1980
en Equipment/Furnishings - Inspection and Possible Rework of Lap Belt and Shoulder Harness Assemblies Manufactured by American Safety Equipment Corporation02/01/1981
en Oxygen - Installation of an Improved Oxygen Control Placard01/01/1981
en Landing Gear - Inspection of Landing Gear Retract Gearbox and RH Torque Shaft for Proper Alignment03/01/1981
en Electrical Power - Inspection for Possible Chafing of Wiring Under RH Cabin Floorboards02/01/1981
en Air Conditioning - Inspection and Possible Replacement of Outflow/Safety Valves02/01/1981
en Electrical Power - Inspection for Clearance between Landing Gear Retract Chain and Air Conditioner Wiring02/01/1981
en Electrical Power - Installation of Power Test Jacks02/01/1981
en Electrical Power - Installation of a Starter Energized Annunciator Light04/01/1981
en Landing Gear - Installation of Improved Main Landing Gear Doors10/01/1981
en Stabilizers - Inspection and/or Replacement of Horizontal Stabilator Aft Center Spars03/01/1981
en Landing Gear - Installation of an Improved Grease Seal and Axle Spacer03/01/1981
en Doors - Installation of a Secondary Latch on Hinged Nose Baggage Door03/01/1981
en Electrical Power - Part I: Inspection of Engine Control Cables for Proper Routing; Part II: Inspection for Transzorbers on Line Contractor Relays; Part III: Installation of 50 Amp Current Limiter on RH Circuit Breaker Panel Feeder; Part IV: Reroute Normal Heat Relay Wires to Improve Cable Clearance03/01/1981
en Doors - Installation of a Secondary Latch Mechanism on Hinged Nose Compartment Door03/01/1981
en Flight Controls - Inspection For Proper Routing of LH Rudder Cable03/01/1981
1 en Fuselage - Inspection of Shoulder Harness Attach Bracket06/01/1981
en Engine Indicating - Modification and Calibration of Aircraft Instrument and Development Incorporated Engine Instrument Clusters03/01/1981
en Equipment/Furnishings - Increase Clearance Between Seatback Pan and Shoulder Harness04/01/1981
en Placards and Markings - Installation of Wing Bolt Torque Information Decals08/01/1981
1 en Air Conditioning - Installation of Insulation Retainers on Heat Exchangers02/01/1983
en Electrical Power - Inspection For and/or Replacement of Aluminum Wires06/01/1981
en Engine Controls - Modification of Carburetor Mixture Control Arm07/01/1981
1 en Doors - Installation of a Secondary Latch Mechanism on Hinged Nose Baggage Door02/01/1983
1 en Engine and Fuel Control - Installation of a Gasket Between Carburetor Air Box and Carburetor08/01/1981
en Landing Gear - Inspection of Main Landing Gear Drag Legs, Drag Leg Bolts & Retract Slide Assemblies for Cracks08/01/1981
en Flight Controls - Installation of a Lift Transducer Reduced Heat on Ground Circuit Panel05/01/1981
en Electrical Power - Part I, Relocation of External Electrical Power Receptacle; Part II, Inspection and Modification of External Power Wiring; Part III, Installation of Upholstery Retainer Clip to Clear External Power Wire Routing10/01/1981
en Propellers - Reidentification of Blades on Hartzell Propellers Equipped with Deicer Boots06/01/1981
en Placards & Markings - Inspection and/or Replacement of Emergency Locator Transmitter Remote Switch Placard06/01/1981
en Wings - Inspection and Possible Rework of Flap Hinge Brackets09/01/1981
en Propellers - Installation of an Improved Propeller Ground Idle Stop System07/01/1981
en Fire Protection - Relocation of Lower RH Fire Detector in RH Nacelle07/01/1981
en Turbines - Modification of Turbocharger Oil System07/01/1981
en Flight Controls - Inspection of Horizontal Stabilizer Forward Spar Web for Possible Working Rivets07/01/1981
en Stabilizers - Inspection of Horizontal Stabilizer Attach Bolts07/01/1981
en Flight Controls - Replacement of Elevator Trim Tab Cable and Drum03/01/1982
1 en Doors - Installation of a Secondary Latch on Hinged Nose Baggage Door04/01/1982
en Fuel - Installation of Improved Fuel Quantity Printed Circuit Boards09/01/1981
en Auto Flight - Inspected and Reinforcement of Sperry SPZ-200A Autopilot Elevator Servo Support Bracket11/01/1981
en Air Conditioning - Installation of a Flow Control Valve Solenoid Cover and Filter10/01/1981
en Engine Fuel and Control - Installation of New Deck Pressure Reference Lines08/01/1981
1 en Fuel - Inspection for Fuel Filler Anti-Siphon Assemblies08/01/1982
en Doors - Inspection of Upper Latch Hooks on Cabin Entrance Door12/01/1981
en Fuel - Inspection and/or Possible Replacement of Airborne Firewall Fuel Filters09/01/1981
en Landing Gear - Inspection and/or Replacement of Brake Master Cylinders03/01/1982
en Exhaust - Installation of Improved Exhaust Pipe Coupling, Bracket & Clamp04/01/1982
1 en Stabilizers - Replacement of Elevators08/01/1982
en Wings - Inspection and/or Replacement of Wing Attach Bolts, Nuts & Inspection of Wing Attach Fittings12/01/1981
en Landing Gear - Replacement of Nose Landing Gear Door Hinge Pins and Replacement of Bushings in Nose Landing Gear Door Actuating Linkage05/01/1983
en Air Conditioning - Installation of Latching Relay Type Pressure Control Printed Circuit Board for Improved Presure Protection & Hole & Cover Plate are Installed in Condenser Access Door06/01/1982
en Landing Gear - Inspection of Landing Gear Emergency Extension System04/01/1982
1 en Electrical Power - Removal of Transzorbers from Avionics Bus Relays11/01/1982
en Windows - Inspection of Fuselage Side Windows to Insure that Multiply Windows are Installed12/01/1982
en Landing Gear - Installation of a Guard on Landing Gear Selector Switch09/01/1982
en Stabilizers - Replacement of Elevators02/01/1982
en Landing Gear - Replacement of Nose Landing Gear Axle03/01/1982
en Landing Gear - Replacement of Nose Landing Gear Attachment Bolts03/01/1982
en Landing Gear - Installation of 17.5 Inch Diameter Tires and Modification of Brake Assemblies01/01/1983
en Power Plant - Modification of Crankcase Breather Tube06/01/1982
en Doors - Inspection and/or Replacement of Airstair Door Roller Assemblies08/01/1983
en Electrical Power - Improved Alternator Feed Diode Installation08/01/1982
1 en Powerplant - Replacement of Engine Mount Assembly and Modification of Engine Control Linkage04/01/1983
en Engine Controls - Installation of an Improved Carburetor Heat Control Spring Detent04/01/1983
en Wings - Installation of Inconel Wing Attach Bolts & Nuts & Inspection of Wing Attach Fittings11/01/1982
en Air Conditioning - Installation of a Retaining Bolt and a Pulley Guard on Air Conditioning Compressor12/01/1982
en Nacelles - To Provide Inspection Plates to Facilitate Engine Mount/Nacelle Channel Inspection03/01/1983
en Flight Controls - Inspection of Rudder Torque Tube Lower Hinge Adapter02/01/1983
en Auto Flight - Installation of Replacement Autopilot Controller for Sperry SPZ-200A Autopilot Control System01/01/1983
en Placards and Markings - To Standardize Emergency Exit Placards and Modify Openable Window Latch10/01/1983
en Power Plant - Installation of Washers on Engine Control Rod Ends01/01/1983
en Fuselage - Inspection for Corrosion at Firewall and F.S. 68.00 Frame02/01/1983
en Lights - Landing Light Wiring Modification04/01/1983
en Fuel - Installation of Improved Fuel Selector Drain Valve02/01/1983
en Fuel - Installation of a Stop on Selector Valve10/01/1983
en Flight Controls - Installation of Parts Required to Ensure Acrobatic Category03/01/1983
en Fuselage - Installation of Improved Cabin Entrance Steps03/01/1983
1 en Engine Indicating - Installation of Isolators for ITT Indicators06/01/1982
en Water Injection - Availability of Water/Methanol Injection Kit08/01/1983
en Stabilizers - Improved Attachment of Rudder Balance Weight09/01/1983
en Fire Protection - Relocation of Lower Forward Engine Fire Detectors10/01/1983
en Ice and Rain Protection - Anti-Ice System Modification
en Landing Gear - Nose Landing Gear (NLG) Piston & Fork Assembly Inspection/Replacement10/01/2021