Service Bulletins: Stoddard-Hamilton| Name | Revision | Lang | Subject | Date |
|---|
| SB 1 |
|
en |
Nose Gear Scissors | 09/06/1984 |
| SB 2 |
|
en |
1. Main Gear Trunnion Actuator Arms; 2. Placement of Partial Spars, Main Landing Gear Support Structure; 3. Possibility of Conflict between Side Brace & Trunnion; 4. Installation of Main Gear Struts and Bearing Housings; 5. Main Gear Mounting Bolts; 6. Hydraulic Pump Solenoids | 11/05/1984 |
| SB 3 |
|
en |
Emergency Gear Extension Spring Tabs | 01/31/1985 |
| SB 4 |
|
en |
Leaking Oleo Struts | 04/29/1985 |
| SB 5 |
|
en |
1. Control Stick Sleeve/Elevator Horn; 2. Spinner Front Plate | 06/28/1985 |
| SB 6 |
|
en |
RG Gear Strut Leaks | 08/05/1985 |
| SB 6 |
A |
en |
RG Gear Strut Leaks | 11/18/1985 |
| SB 7 |
|
en |
Welds on Inboard Rib Attach Brackets Interfere with Washers | 10/17/1985 |
| SB 7 |
A |
en |
Welds on Inboard Rib Attach Brackets Interfere with Washers | 10/31/1985 |
| SB 8 |
|
en |
Defective Fuel Fittings | 11/13/1985 |
| SB 9 |
|
en |
Glasair I RG Shimmy Damper Modifications | 11/14/1985 |
| SB 9 |
A |
en |
Glasair I RG Shimmy Damper Modifications | 03/13/1986 |
| SB 9 |
B |
en |
Glasair I RG Shimmy Damper Modifications | 11/15/1986 |
| SB 9 |
C |
en |
Glasair I RG Shimmy Damper Modifications | 10/22/1987 |
| SB 10 |
|
en |
Battery/Alternator Master Switch | 11/18/1985 |
| SB 11 |
|
en |
S-Tec Autopilot Aileron Actuating Push Rod | 04/09/1986 |
| SB 12 |
|
en |
F3416M Rod End Bearings | 05/15/1986 |
| SB 13 |
|
en |
RG Printed Circuit Boards | 05/30/1986 |
| SB 14 |
|
en |
Fixed Pitch Spinner Backplates | 05/30/1986 |
| SB 15 |
|
en |
Oildyne Hydraulic Pump Fittings | 09/30/1986 |
| SB 16 |
|
en |
New Style Gas Cap Seal | 09/30/1986 |
| SB 17 |
|
en |
Derakane Vinyl Ester Resin | 10/16/1986 |
| SB 18 |
A |
en |
Mandatory Fuel Contamination | 10/16/1986 |
| SB 19 |
|
en |
Engine, Propellers and Propeller Governors for Glasair III | 12/08/1986 |
| SB 20 |
|
en |
Electrical System; 28v Option | 12/15/1986 |
| SB 21 |
|
en |
Fuselage Panel Modifications | 12/31/1986 |
| SB 22 |
|
en |
Fitting of Engine Mount | 01/08/1987 |
| SB 23 |
|
en |
Gap between Nose Wheelwell Box and Firewall | 03/31/1987 |
| SB 24 |
|
en |
Glasair III Horizontal Stabilizer Stiffening | 01/31/1987 |
| SB 25 |
|
en |
Contouring of Upper Surface Main Spar Cap | 06/25/1987 |
| SB 26 |
|
en |
Glasair RG Nose Gear Drag Brace Reinforcement | 03/10/1987 |
| SB 27 |
|
en |
Instrument Panel Template 3G1501 | 02/23/1987 |
| SB 28 |
|
en |
Fitting of Various Glasair I Parts to Glasair II Fuselage | 03/10/1987 |
| SB 29 |
|
en |
Fitting of Early Model Landing Gear Boxes | 06/25/1987 |
| SB 30 |
|
en |
Landing Gear Box Forward Partial Spar Support Fabrication | 06/25/1987 |
| SB 31 |
|
en |
Erroneous Firewall Rib Location | 03/05/1987 |
| SB 32 |
|
en |
Glasair III Engine Mount & Firewall Template | 03/19/1987 |
| SB 33 |
|
en |
Glasair III Engine Mount & Firewall Template | 03/19/1987 |
| SB 34 |
|
en |
Hole Size in First Production Run Flap Ratchet Plates | 06/25/1987 |
| SB 35 |
|
en |
Correct Control Stick Sleeve for Glasair II | 08/20/1987 |
| SB 36 |
|
en |
Mandatory Inspection for Fuel Leakage Around Main Spar Attach Fitting Bolts | 06/25/1987 |
| SB 37 |
|
en |
Glasair II Lower Wing Panel with Glasair III Wheelwell Scribe Lines | 06/25/1987 |
| SB 38 |
|
en |
Location of Flap Control Assembly | 06/25/1987 |
| SB 39 |
|
en |
Glasair Taildragger Main Landing Gear Upper Attach Bolts | 08/31/1987 |
| SB 40 |
|
en |
Relocation of Hydraulic Pressure Gauge Sensing Point | 09/30/1987 |
| SB 41 |
|
en |
Oildyne Hydraulic Pump Pressure Increase | 09/30/1987 |
| SB 42 |
|
en |
Inadequate FT Nose Wheel Pivot Range | 10/15/1987 |
| SB 43 |
|
en |
Possible Incorrect Cable Thimble Installation | 10/08/1987 |
| SB 44 |
A |
en |
Glasair FT Nose Landing Gear Modification | 01/09/1989 |
| SB 45 |
|
en |
Possible Incorrect Rudder Pedal Center Support Bracket | 10/29/1987 |
| SB 46 |
|
en |
Mislocation of Nose Wheel Axle Roll Pin Holes | 12/28/1987 |
| SB 47 |
A |
en |
Mandatory Hydraulic Actuator Piston Retaining Nut | 11/30/1995 |
| SB 48 |
|
en |
Canopy Frame Modification | 03/31/1988 |
| SB 49 |
|
en |
Erroneous Dimensions of Firewall Flange Template, Revision A; P/N 400-0016-03 | 03/31/1988 |
| SB 50 |
|
en |
Erroneous Trim Lines on Left Canopy Frames | 04/14/1988 |
| SB 51 |
|
en |
Possible Nose Gear Drag Brace Binding | 04/15/1988 |
| SB 52 |
|
en |
Main Gear Hydraulic Actuator Rod Retrofit | 05/17/1988 |
| SB 53 |
|
en |
Possible Interference between Elevator Actuator Arm & Rudder Actuator Linkage | 07/15/1988 |
| SB 54 |
|
en |
Elevator Counterweight Arm Modification | 07/15/1988 |
| SB 55 |
|
en |
Possible Play between Prop Extension & Lug Bushings for Fixed Pitch Propellers | 07/15/1988 |
| SB 56 |
|
en |
Nose Gear Down Lock Spring Installation | 07/15/1988 |
| SB 57 |
|
en |
Mandatory Side Brace Bellcrank & Side Brace Upper End Bushing Replacement | 07/20/1988 |
| SB 58 |
|
en |
Rudder Pedal Assembly Interference with Nose Gear Support Ribs | 09/08/1988 |
| SB 59 |
A |
en |
Trim Control Wheel Shaft Modifications | 11/03/1988 |
| SB 60 |
|
en |
Defective Hydraulic System Tubing | 10/24/1988 |
| SB 61 |
A |
en |
Fuel Leaks through Spar Caps | 01/09/1989 |
| SB 62 |
|
en |
Possible Wing Leading Edge Interference with Nose Gar Box and Fuselage Reinforcement Rib | 11/23/1988 |
| SB 63 |
|
en |
Mislabeled Terminals on Gear Retract Printed Circuit Board | 03/01/1989 |
| SB 64 |
|
en |
Mounting Hole Locations in Main Landing Gear Forward Side Brace Brackets | 03/06/1989 |
| SB 65 |
|
en |
Mandatory Facet Electric Fuel Boost Pump Alert | 03/27/1989 |
| SB 66 |
|
en |
Lorde Engine Suspension Assemblies | 06/06/1989 |
| SB 67 |
|
en |
Trim System Interference between Cable Drum & Trim Control Box Housing | 08/31/1989 |
| SB 68 |
|
en |
Cabin Heat Box Gasket | 09/07/1989 |
| SB 69 |
|
en |
Mandatory Elevator Counterweight Reinforcement | 09/07/1989 |
| SB 70 |
|
en |
Induction System Fatigue Improvements | 09/07/1989 |
| SB 71 |
A |
en |
Mandatory Inspection Requirements for Glasair III Engine Mounts | 10/17/1991 |
| SB 71, Supp A |
C |
en |
Mandatory Inspection Requirements for Glasair III Engine Mounts | 01/02/1996 |
| SB 72 |
|
en |
Glasair III Hydraulic Snubber | 09/11/1989 |
| SB 73 |
|
en |
Possibly Incorrect Engine Mount Nuts | 11/30/1989 |
| SB 74 |
|
en |
Clearance between Exhaust System & Oil Cooler | 11/30/1989 |
| SB 75 |
A |
en |
Mandatory Replacing RG Nose Gear Fork Attach Bolts | 05/03/1990 |
| SB 76 |
|
en |
Landing Gear Toe-in Alignment Procedures | 03/26/1990 |
| SB 77 |
|
en |
Mandatory Main Gear Hydraulic Actuator Rod-End Reinforcement | 03/26/1990 |
| SB 77, Supp A |
|
en |
Mandatory Main Gear Hydraulic Actuator Rod-End Reinforcement | 11/18/1993 |
| SB 78 |
|
en |
Various Nose Gear Installation Problems | 03/26/1990 |
| SB 79 |
|
en |
Nose Gear Emergency Extension Gas Spring | 04/02/1990 |
| SB 80 |
|
en |
Mandatory Nose Gear Shimmy Damper Compression Spacer Removal | 04/25/1990 |
| SB 81 |
|
en |
Possible Cracks in Spinner Backplates for Fixed Pitch Wooden Propellers | 04/30/1990 |
| SB 82 |
|
en |
Mandatory Possible Cracks in Glasair III 90 Degree Induction Elbows & Support Arms | 05/01/1990 |
| SB 82, Supp A |
|
en |
Mandatory Possible Cracks in Glasair III 90 Degree Induction Elbows & Support Arms | 12/20/1990 |
| SB 83 |
|
en |
Cosmetic Paint Cracks at Base of Windshield | 05/01/1990 |
| SB 84 |
|
en |
Main Tank Fuel Gauge Components for Glasair II-S | 05/03/1990 |
| SB 85 |
|
en |
Nose Gear Wheelwell Firebarrier Installation | 05/03/1990 |
| SB 86 |
|
en |
Lycoming AD Concerning Propeller Governor External Oil Line | 05/03/1990 |
| SB 87 |
A |
en |
Seat Belt Attach Angle Fabrication | 06/22/1990 |
| SB 88 |
|
en |
Mandatory Incorrectly Labeled Main Gear Side Brace Assemblies | 05/31/1990 |
| SB 89 |
|
en |
Mandatory FT Nose Gear Strut Reinforcement | 10/15/1990 |
| SB 90 |
|
en |
Mandatory Rudder Actuator Linkage, Incorrect Length | 12/07/1990 |
| SB 91 |
|
en |
Mandatory Failure of Alternate Air Door Spring (Injected Induction System) | 12/10/1990 |
| SB 92 |
|
en |
Mandatory RG Nose Gear Emergency Extension Gas Spring | 12/12/1990 |
| SB 93 |
|
en |
Mandatory Revised Gross Weight & Main Landing Gear Strut Replacement | 12/14/1990 |
| SB 94 |
|
en |
Elevator Hinge Brackets (P/N 552-4423-001) | 12/17/1990 |
| SB 95 |
|
en |
Mandatory Glasair III Landing Gear Oleo Strut Welded Joints | 12/19/1990 |
| SB 95, Supp A |
|
en |
Mandatory Glasair III Landing Gear Oleo Strut Welded Joints | 08/19/1991 |
| SB 96 |
|
en |
Mandatory Elevator Trim Box Main Gear Assembly | 12/21/1990 |
| SB 97 |
|
en |
Incorrect Placement of Pedals on New Style Rudder Pedal Weldment | 01/31/1991 |
| SB 98 |
|
en |
Slotted Flap Hinge Point Corrections | 02/01/1991 |
| SB 99 |
|
en |
Mandatory Landing Gear Electrical System Wiring Change | 03/01/1991 |
| SB 100 |
|
en |
Mandatory Nose Gear Drag Brace, Possible Failure to Lock Over-Center | 05/28/1991 |
| SB 101 |
|
en |
Mandatory Fuel Filter Assembly, Inspection & Modification | 07/08/1991 |
| SB 102 |
|
en |
Forward Fuselage Belly Section Foam Core Placement | 07/08/1991 |
| SB 103 |
|
en |
Mandatory Nose Gear Over-Center Springs | 08/15/1991 |
| SB 104 |
|
en |
Mandatory 3/16" Aluminum Tubing for Brake Lines (Lot# 90-6980, 6/2/89) | 08/20/1991 |
| SB 105 |
A |
en |
Mandatory Retractable Landing Gear Oleo Strut, Weld Inspection & Repair | 11/07/1991 |
| SB 106 |
|
en |
Mandatory Bolts Securing Elevator Hinge Brackets to Stabilizer Shearweb | 11/21/1991 |
| SB 107 |
|
en |
Barry Control Standard Engine Vibration Isolators for Glasair III | 12/19/1991 |
| SB 108 |
|
en |
Mandatory Glasair III Cowl Flap Rod End Bearings (Stoddard-Hamilton Stock No. 170-0110-003) | 01/09/1992 |
| SB 109 |
|
en |
Mandatory Glasair III Nose Gear Hydraulic Actuator Rod | 01/10/1992 |
| SB 110 |
|
en |
II-S FT Outboard Main Gear Strut Attach Bracket Installation | 04/15/1992 |
| SB 111 |
|
en |
Mandatory Flap Plunger Bolt, Possible Failure | 04/30/1992 |
| SB 112 |
|
en |
Mandatory Center of Gravity Location & Longitudinal Stability and Control for Glasair II-S FT | 05/20/1992 |
| SB 112, Supp A |
|
en |
Mandatory Center of Gravity Location & Longitudinal Stability and Control for Glasair II-S FT | 10/26/1992 |
| SB 113 |
|
en |
Mandatory Center of Gravity Location and Longitudinal Stability and Control for Glasair II-S TD | 05/20/1992 |
| SB 113, Supp A |
|
en |
Mandatory Center of Gravity Location and Longitudinal Stability and Control for Glasair II-S TD | 11/26/1992 |
| SB 114 |
|
en |
Mandatory Center of Gravity Location and Longitudinal Stability and Control for Glasair II-S RG | 05/20/1992 |
| SB 114, Supp A |
|
en |
Mandatory Center of Gravity Location and Longitudinal Stability and Control for Glasair II-S RG | 10/26/1992 |
| SB 115 |
A |
en |
Mandatory Fuel Selector Valve, Inadvertent Shut-Off | 11/18/1993 |
| SB 116 |
|
en |
Mandatory Wing Tip Extensions, Large Rudder Requirement | 07/20/1992 |
| SB 117 |
|
en |
Mandatory Alternate Air Door - Possible Fatigue Separation Leading to Ingestion of Metal Particles into Engine | 11/09/1993 |
| SB 118 |
A |
en |
Mandatory TD Main Landing Gear Position | 12/15/1993 |
| SB 119 |
|
en |
Mandatory Backup Drag Brace Microswitch Installation of G-III Nose Gear | 11/09/1993 |
| SB 120 |
|
en |
Mandatory Shoulder Harness Attachment | 11/18/1993 |
| SB 121 |
|
en |
Mandatory Early Black Intermittent Duty Solenoids | 11/18/1993 |
| SB 122 |
|
en |
Navigation Antenna Length | 11/18/1993 |
| SB 123 |
|
en |
Mandatory FT Outboard Rib Attach Landing Gear Brackets | 11/18/1993 |
| SB 124 |
|
en |
Mandatory G-III Main Gear Side Brace Bellcrank Bracket Bushings | 11/18/1993 |
| SB 125 |
|
en |
Mandatory Glasair I RG Cast Scissors | 03/24/1994 |
| SB 126 |
|
en |
G-III Main Landing Gear Strength Upgrade | 01/10/1995 |
| SB 127 |
|
en |
RG Hydraulic System Filters | 01/10/1995 |
| SB 128 |
|
en |
Hydraulic Pump Upgrade Offer | 01/10/1995 |
| SB 129 |
|
en |
Mandatory Drag Brace Weld Clearance Inspection | 01/10/1995 |
| SB 130 |
|
en |
Mandatory Sealing Fuel Filter Bowl Securing Bolt | 01/10/1995 |
| SB 131 |
|
en |
Fuel Venting Overboard | 01/20/1995 |
| SB 132 |
|
en |
Glasair Super II-S Rudder Pedal Control Weldments | 01/10/1995 |
| SB 133 |
|
en |
Revised Gross Weight & Main Landing Gear Strut Replacement | 01/10/1995 |
| SB 134 |
|
en |
Mandatory Directional Control on Take Off | 01/10/1995 |
| SB 135 |
|
en |
Mandatory FT Outboard Rib Attach Landing Gear Bracket | 01/10/1995 |
| SB 136 |
|
en |
Hydraulic Actuator Seal Damage | 01/10/1995 |
| SB 137 |
A |
en |
Mandatory Glasair III Main Landing Gear Side Brace Stud Replacement | 08/01/1996 |
| SB 138 |
|
en |
Mandatory Electric Tim Turnbuckle Replacement | 09/01/1995 |
| SB 139 |
|
en |
Mandatory Glasair I/II RG, PC Boards what were Shipped with "Option I" Diodes in Place | 11/30/1995 |
| SB 140 |
|
en |
Mandatory Elevator Torque Tube Assembly Welds | 11/30/1995 |
| SB 141 |
|
en |
RG Landing Gear Scissor Bolt Bushing Installation | 11/30/1995 |
| SB 142 |
|
en |
Mandatory AN470A4-7 Soft Rivets | 11/30/1995 |
| SB 143 |
|
en |
Mandatory Glasair III Nose Gear Drag Link Studs - Possible Weld Failure | 07/30/1996 |
| SB 144 |
|
en |
Mandatory Tubing Flaring Tool (P/N 810-0190-001) | 07/30/1996 |
| SB 145 |
|
en |
Glasair III Rod-End Bearings (P/N 170-0110-003) | 07/30/1996 |
| SB 146 |
|
en |
Mandatory Glasair II-S FT & Super II FT Nose Gear Trunnion Attach Plate Fasteners | 09/05/1996 |
| SB 147 |
A |
en |
Mandatory Main Gear Half Fork Attach Bolts | 11/11/1996 |
| SB 148 |
|
en |
Mislabeled CoNap & DMA Promoter | 11/21/1996 |
| SB 149 |
|
en |
Mandatory Main Landing Gear Trunnion Tubes, Possible Cracking | 03/03/1997 |
| SB 150 |
|
en |
Mandatory Fram Fuel Filter Assembly (P/N 332-0341-101) | 02/26/1998 |
| SB 151 |
|
en |
Mandatory AN470A4-9 Soft Rivets | 02/26/1998 |
| SB 152 |
|
en |
NicoPress Sleeves (P/Ns 450-0002-003, -004 & -015) | 12/08/1998 |
| SB 153 |
|
en |
Aileron Counterweight Assemblies | 12/08/1998 |
| SB 154 |
|
en |
Mandatory Gear Warning Buzzer (P/N 210-0677-001) | 12/08/1998 |
| SB 155 |
|
en |
Mandatory Airborne 211CC & 215CC Vacuum Pumps (P/N 120-0211-001) | 12/08/1998 |
| SB 156 |
|
en |
Mandatory Resin Coating of Glasair III Wing Fuel Bays | 02/02/2005 |
| SB 157 |
|
en |
Glasair IIS 200hp RG Engine Mounts; P/N 222-0269-103 | 03/18/2005 |
| SB 158 |
|
en |
Glasair III Engine Mounts: P/N 223-1420-101 | 11/30/2005 |
| SB 159 |
|
en |
Prop Governor Gasket | 05/02/2007 |
| SB 160 |
|
en |
Nose Gear Axle Nut | 05/04/2007 |
| SB 161 |
|
en |
Inspection of RG Gear Oleos for Corrosion | 06/09/2008 |
